12: HYDRAULIC DOORS

1

Please quote a 42' X 14' Standard Hydraulic Flush Mount Door. Project Address: Jeffersonville, Indiana 47130 Design - Build General Contractor: AML Inc.

2

I am designing an enclosed structural skid that needs hydraulic doors for service of tall components in New Jersey. Minimizing head room loss is critical for this application, as the height of the enclosure from the floor to the top-most point on the structure can only be 11' 6", and the clear opening height must be at least 9'6" (ideally 10').

3

Hi, We are a spanish company, and we want information about your hydraulic system. Do you have dealer in Spain or Europe?. I wait for Your information. King regards.

4

Hello sir or ma’am, Can I please get a cost for a 20’x14’ and a 16’x14’ hydraulic door going to Nebraska? Thanks

5

I have a an airplane hanger project and need to find the below motors for this project. Can you help me? Motor shall be 3/4 H.P. (minimum) 230 V.A.C. single-phase thermally protected and supplied with a reset button. Motor SP-16 shall be totally enclosed capacitor start. Cable drum shall be a direct drive drum by shaft mounted gearbox. Gearbox shall be oil bath two-stage gearbox, bronze worm gear, hardened steel spur gears, tapered roller and ball bearings. Door operator shall be pre-wired at factory complete with 24 V.A.C. momentary up and down pressure-down push button control, magnetic controllers, geared rotary limit switch attached to cable drum designed to coordinate reversing operation, spring set electric brake, and up-stop safety switch; over-ride safety mercury tilt switch to disconnect power in case of over travel. Power connection shall be by heavy-duty 230-volt plug for easy connection.

6

Hello, I am wanting to build an aircraft hangar here in spearfish, SD 57783 I have contacted several building/door manufactures and was wondering if i could get a quote from Schweiss Hydraulic Doors on a one piece (not bifold) hydraulic door. Size 55X19? Give me window passenger door options please. Thanks

7

We need a quote for a new hangar we are building. The door we want is a schweiss hydraulic door, 50 wide x 14'6 tall. We have schweiss doors already on another hanger but this one we want to see if we can get the door truss moved up the door rather than at the bottom? We find it problematic in the winter in Alaska trying to clear snow prior to raising the door. We look forward to a quote. Thanks

8

Looking for budget pricing for a 20'x10' schweiss bifold hydraulics door with metal cladding. A price range is acceptable.

9

Pricing a project in New Caanaan Ct Calls for 9x20 hydraulic door clad in cedar. Also need names of local installers.

10

I'm bidding a project in Hollywood South Carolina with A 40'W X 12H Canopy Hanger Door.I would to match the doors used at Scout Boats in S,ville SC. .460 volts 3 phase .CCS to supply and install sheets.

11

Need an estimate on a one piece fold up door for my outdoor grill enclosure. The dimensions are roughly 11 ft. 9in. Wide x 7ft 6in. Tall.

12

looking for a qoute on one piece hydraulic door installed. Evansville, Mn please provide all glass qoute as well one that steel siding can be installed upon. thank you

13

I have a 60'x50' concrete block airplane hangar at North Perry Airport in Pembroke Pines, Florida. It has a 40' Schweiss 4 strap door. The hangar is 20 years old and the door works perfectly. I am building a new concrete block hangar at my home on Big Whale Cay, Berry Islands, Bahamas. I need a price for a 50' wide by 18' high 5 strap door for the new hangar I am building on Big Whale Cay. I am now interested in a hydraulic door. Thanks,

14

Good morning could I get a price on a Hydraulic door looking for a price on the following door. 30X16

15

I have a client looking for a hydraulic door. 32'x18' I need to get a price together for him also need to know if the price includes install and set up. Need to know what power and cut sheet for opening, thanks.

16

We have a Rough opening of a Concrete garage structure that has already been poured and has the exact dimensions listed below. We need a quote for a hydraulic door that fits in the dimension and mounts directly into the concrete.

17

Hello - I am looking to get a hydraulic door for my custom home gym around 10-12 feet in width, maybe 8-10 feet high. Curious the budget needed for this and what the process is like. Thanks, Cam

18

I am estimating a job in Bartow, FL. I need a price for some hydraulic hangar doors. I can provide the plans and specifications. Can you assist me in pricing this project? Thanks,

19

I am looking for a new door for an 80x80 hangar I'm building. I am interested in bottom rolling, hydraulic and maybe bifold in that order. (I have two Schweiss bifold doors). I need 12 foot clear height and 70-75 foot width. I will be putting windows in the upper part of the door to create a vintage look.

20

I need a quote on 4 hydraulic doors approximately 11'x39'6" in size to be installed at Harlan, Iowa.

21

Hello I am quoting a new construction 50x96x18 pole type building, built on a 4' stem wall, the customer has requested a +-16x40 hydraulic door be installed. I am also quoting this as a steel structure as well. Please quote Thank You

22

I am interested in a price for a lift strap door on a garage. The garage door opening is 9' x 26'. This garage is completely off the grid. I have electricity , 120v and 229v, from solar with batteries and a generator. I bought a saw mill and milled all the wood from timber on the property and built the building myself. I need a door that girls can operate and is theft proof. It will be shipped to Madera California and I will take it to the 315 myself. Thanks,

23

We are in need of 4 hydraulic style doors. 3@8'x8' 1@9'wx10'H the larger door needs to have a 3'x8' man door built into the frame on the left side of the door looking in. The building will have concrete for fastening.

24

We are interested in a 50' x 16' hydraulic door on a storage building for a local farmer. Would like a price as well as details on design specs necessary or it to be installed in a pre-engineered steel building.

25

We have a hydraulic door. We are wondering if you have a dealer in our area that can provide service. Can you provide service or let us know who can come maintenance this door?

26

I am an architect designing an aircraft hangar in Kansas and putting details together in construction drawings. The door sizes we are aiming for are 44'-6" wide clear by 14'-0" tall clear. We are looking for a hydraulic door and will have steel columns on either side spaced at 45'-0". Are you able to send any 2D CAD drawings that I can design around? This will be bid competitively outside our office, so we are just using for the basis of design. Anything would be helpful. Thank you.

27

Existing pole shed with dual sliding doors. Opening is 26' 6" wide by 14'4" tall. I would be the most interested in the frame and hydraulic package. I would like to use the old tin for the outside shell, along with insulate and line the interior myself. Possibly 2 windows nothing large.

28

I have an existing aircraft hangar with wood sliding doors. At the top of the opening is a steel header. I'm trying to find a new door that will not intrude on the height of the opening, or if so very little. I would like to learn more about your product.

29

I am looking for a quote on a 60x18 stand alone hydraulic door for a hangar we are quoting. The door will have 3-60x42 inch windows installed in it. Would like the quote to include installation of the door. We can install the exterior skin.

30

Hello, I'm a project manager from Flatiron Corp. I'm currently supervising a new government project and we're interested in purchasing some of your products including commercial hydraulic doors with exact quantities and specifications to be provided. kindly have your representative contact us for confirmation regarding the availability of the aforementioned products, along with the necessary procedures for collaborating with your company. Your prompt response is greatly appreciated. Best Regards.

31

Please price out 45x16 hydraulic door. The wall height will be 16'. Please call or email with questions. Thank you. If you can also price out the labor to install this would be fantastic also.

32

I am in need of two 40’ long by 20’ tall hydraulic bifold doors. I have never messed with this type of door before, and was wondering how much it would cost to have them installed.

33

Cleary is a gc company that builds commercial buildings for clients, the client I am working with is trying to buy a t-style hange or just a single hanger depending on the price of it all. So my question is, I need a quote for a 42'wide x 14' tall hanger door the client would like accordion stlye but if you do not have those then a fold up would work, not a bi-fold but single lift door.

34

hello, i want to build a hangar and i need a door for this project. the open section of the hangar is 16m(52,49ft)x3,50m(11,48ft).

35

Hi, I am contacting you from Australia. I have a unique door set up which require automation and which I think needs hydraulic because of its geometry. Would you be interested in supplying your product to us if it fits our requirements

36

We have a multifamily project currently under construction that has a separate retail building calling for (3) 12' wide by 10' tall hydraulic top-swinging doors to mimic adjacent storefront windows. We are looking for pricing as soon as possible as this project is well underway. Thank you for your assistance.

37

I need a quote for 48’x16 clear door. Also need to know framed opening height required for this door

38

Working on a project that would have six 20'by14" Hydraulic doors. Are your doors self support or do they rely on the buildng manufactuer? Could you give me a call or a budget number for each door?

39

We're reaching out to get more information about Hydraulically Operated Doors. Your product is being considered to be included in the specifications for the new Theodore Roosevelt Presidential Library in North Dakota. Would you please put us in direct contact with the best person in your company to answer questions about sustainability and product chemistry related to LEED and the Living Building Challenge?

40

I need an estimate for 4 hydraulic doors. How much room do I need on either side of the door? can the hydraulics be mounted from the ceiling?

41

Need a quote for 50x14 hydraulic door. Need 13' clearance. please give me a quote for both wood and steel building.

42

Looking for hydraulic door going to Campbell county tn. 44x14 clear. Would like bottom truss. 12v backup for pump. And remote opener. Could you give price.

43

I have a job that is interested in 3 one piece swing up doors Sizes 16x8, 9x8, 12x8

44

Bidding a job wanting a 40’x18’ hydraulic doors I bought and installed a hydraulic door in 2013

45

Hi, I am looking for a 10' x 8' perforated metal tilt-up door. Please quote me a price for the door and a price for the installation. Thank you.

46

Need door quote 50 wide X 20 High hydraulic door complete system. Goes in endwall of 100x200 steel building

47

Needing a 50'X18' Hydraulic door quoted for Red Iron building in Salem, South Dakota. Please get ahold of me when you can. Thanks

48

I would like to upgrade the cable system on my bi-fold door to straps. Roughly 52' x 16'. Newnan, Georgia KCCO. Can I get an estimate, and can you recommend a contractor to install (or send your guys)? I'm a recent customer. Love my hydraulic door in Apalachicola FL (KAAF)!

49

Hi, I was wondering if you have any hydraulic systems that can open and close a door against a 20 knot wind. It is a hinged door swinging open just as a normal door would do, not upwards. The door dimensions are 3m width x 5m height, 1760 kg leaf mass. Thank You

50

need quote on 40 x 12 hydralic door ,installed in Shelbyville,KY. on a new walters Building

51

I am looking for a price on a 60x14 Hydraulic Door. I have installed a 60x16 Hydraulic door of yalls and it was very simple and yalls instructions made the process quick! I would also be interested in more information on being a dealer/installer and how all that works.

52

I see that the hydro doors have a battery backup but I have a customer who does not have electrical power. Can the system work off of a battery system that is charged by solar??

53

Looking for an estimate: Full view door Hydraulic To replace our roll up garage door that is 93”h x 176”w

54

door opening is approximately 18x 40 feet . could you give me an idea of cost on hydraulic door

55

Looking for pricing for a 15' hydraulic door to be installed into a 40' sea can. Sea can is 9'6 tall, so the door would be approx. 8'.

56

The hydraulic door will also need to be able to hold an interior liner and thermax insulation.

57

Looking for pricing on a 60W x 14H Hydraulic door with 2 walk doors and 4 windows (6'w x 5'h) Door will be sheeted with metal building panels

58

We'd like to learn more about your hydraulic doors. Do you offer any AIA learning units that we could do with you remotely? DJM, AIA

59

We will be building a 100x80x18 steel building this coming spring. I’d like a quote on a 25x18 hydraulic door. No windows…just wainscot. Is there any additional frame work that would need to be installed? Thanks, AP

60

Opening size is 26' wide with 13' to bottom of truss It should be outside mount so we can maximize inside footprint We would like it to be schweiss hydraulic single door (not bifold) Would like to have a 24" row of windows at the 60" height We will install --Power available 240V 3 Ph

61

Good day How are you? Kindly provide us a quote for four hydraulic one piece doors, roughly 60x20. Awaiting your response.

62

We have an opportunity to replace 14 hydraulic doors on the Island of Kauai in Hawaii . Do you have certified installers ? 6- 45.6 x 15.9 8- 39.6 x 14.04 We would like to speak to you about this project 14 doors total

63

A friend told me to reach out for pricing on (2) single swing hydraulic doors. They are 22' x 10' and 11' x 10' approximately. Please give me a call or reach out to my by email. Thanks, Stan

64

We have a brand X hydraulic door and occasionally it will not lower. sometimes we can get it to work by pushing the control buttons simultaneously. Lately that did not correct problem. After it sits overnight it will go down. I don't think they're in business anymore, could you guys take a look?

65

I have a T hanger two side sliding folding doors with one piece swing up overhead door Getting more difficult to open center door. Can I get a quote on a new one piece hydraulic door? Thanks

66

We have an older wood frame barn we are rebuilding into a shop and have an end door opening of approximately 16 tall by 26 wide, we're thinking we want a hydraulic door. We are located in northeast Missouri

67

hi, i have a door opening 23' x 10'9" in a farm building, considering installing a hydrualic door. thanks.

68

i need a quote for 8 doors 8 meter wide and 4 meter tall, white panel and no window, with all the hydraulic system.

69

I need a Price & technical data for the Least Expensive, 60' x 14'  hydraulic hangar door, going to Gainesville, TX

70

Hello, I am looking to price a 40' x13' hydraulic hangar door to go in a proposed building near Pilot Rock Oregon. Please see attached preliminary drawings to give you an idea of the building layout. Please feel free to call or email me with any questions you might have. I am looking for a supply and install number if you can get it. The sooner the better. I would like to be able to submit by the end of the week Thank you for your time, have a great day. Bill

71

Need a quote for a 23feet 6 inch wide by 16feet 7 inches high hydraulic door Asap. Thanks much

72

We are currently quoting on a building project and it requires a hydraulic door with an opening of 48'w x 16'h clear. Please let me know what other information you require for this project. Thx Debra

73

I need a quote on a hydraulic 40' x 11' hangar door. to be installed in a Morton Hangar in Ocala FL. Must include engineered plans, freight, equipment, seals, hydraulic oil, and everything needed to complete job. Morton will skin and trim door. Thank you, -Sam

74

Looking for individual prices for the following to suite 4 Hangar doors 40'ft x 12'ft. Hydraulic Door Hinges Hydraulic Mounting Flanges 24v Hydraulic power pack

75

I have a 6'7" tall carport that seems to be too short for the standard automatic door opener. I'm looking for an alternative, such as your hydraulic openers to accommodate my low ceiling and allow cars to park inside the car port. I'm working how much the hardware would be.

76

I have 2 of your cable bifold doors. Looking at the purchase of a flat storage site that needs a door. Although an agreement on the purchase of the site has been reached, I will need to wait for corporate approval. So, could be December before I get possession. BUT, wondered if one of your sales reps is in the area sometime that you could maybe stop and look at the building and give me a quote on installing a one piece hydraulic door. Dale

77

I am interested in your green power pump set up. My shop built door has worked ok for 12 years but I need a better on/off control and positive pressure to hold the door shut without latches. I am interested in specs and prices. Give me a call. Thanks, Bill S.

78

Please send me a quote for a hydraulic door that is 10 feet high by 12 feet wide. 

79

I am looking for budgets and cut sheets on 3 hydraulic doors, a 70 ft wide by 24 ft high door, an 80 ft wide by 26 ft high door, and a 100 ft wide by 28 ft high door. Please make recommendations and provide possible options. Thank you, Paul S.

80

I have a customer that wants (2) 60'Wx20'H Schweiss one-piece hydraulic vertical lift doors installed on a 120' wide building. Is this possible with the corner columns? If so, can I get a price on these doors?

81

I am still looking and pricing out buildings, but I am looking for a minimum of a 10' clear opening, I think a hydraulic door will be best for what I'm looking for...please advice on how tall of a building I'd need.

82

The building is a new structure going up. We are currently planning on a 26 foot overhead door. Would one of your one piece hydraulic doors work. The door needs to be on the eve side. Not the gable end. We already have one of your doors in our shop and love it. Door size is 26' wide x 14' high

83

After I found your contact information on your Schweiss Doors website I was sold on your doors, especially your hydraulic doors. You detailed all of the information I was looking for, and now I see why people say you manufacture the best bifold and hydraulic doors on the market. I'll soon be placing an order for a designer door for my restaurant. What is your door lead time?

84

I am considering a 40 foot addition to an existing building. It will have 16 foot of clearance under the rafters. I would like to install a Schweiss Red Power hydraulic door in the side of this 40 foot addition. I would like to have 16 foot of clearance. I am thinking 30 foot wide. What do I need to consider as I design this addition?

85

I am looking at converting an existing building into a heated shop and I am looking for a door that is 25 feet wide by 13 feet tall I am looking at a hydraulic door as I want to keep as much head room as possible, I'm also very impressed with your Red Power Pump setup. If you would, you can send me a quote at my email address thank you

86

We have 4 custom designed benches that are hinged to permit access to fountain controls below the benches. Unfortunately, each of the hinged sections weighs @ 800lbs. We need to provide a lift system to permit a single worker to access under the benches daily. Do you offer a product suitable? The application is exposed to the weather. I'm thinking maybe your Schweiss hydraulic Red Power pump door system might be the ticket. Your thoughts?

87

Hello, am interested in more information regarding your commercial hydraulic doors. More along the lines of image (24) from your Schweiss Doors home page. Thank you.

88

We are looking for a quote and design loads for a 45'x18' hydraulic Schweiss door. Windows, insulated and installed.  If you have any questions, please contact me. Thank you

89

Please see attached written specifications and hydraulic door schedule. Can you please give us a price on this door? Opening is 20\' wide by 9\'5\" high It will be Red Power electrically operated, and sheeted with wood (by customer) Please include any options you might recommend as well as shipping information We are located in Victoria, B.C. V8Z 3B8, Canada

90

I have an existing metal building that is 40\'x72\'x12\'. It has a 20\' w x 13\'h overhead door. The owner would like to replace the overhead door with a 30\'w x 13\'h hydraulic Red Power door. The door would be insulated with spray foam insulation and then lined with liner panel. Please price window options also. Can you help me out with what reinforced would need to be done to the existing end wall to support this? Please submit quote for this work. Price FOB

91

Door opening is approx.. 20\'X 15\' with steel I-beam at top supported by 4\"x 6\" tube columns. I am interested in an approx. cost of a Schweiss hydraulic Red Power pump door. As a retired Gen. Contr., I would install myself and would supply my metal wall panels and insulation. My location is eastern Iowa zip code 52060.

92

Hello, I'm inquiring about general budget pricing for several hydraulic one piece Schweiss doors at the size specified below. If 8' high doors do not allow enough clearance to walk under the door when raised, please quote doors sized to allow 7' clearance when opened. This is for a new roof top structure as an addition to an existing building. We'd like to see if this product could be at all possible within our budget. Thanks.

93

I quoted my customer an airplane hangar 3 years ago with a competitors Hydro door. My metal building Manufacturer has told me they are out of business and to contact you for pricing. He also noted that Schweiss makes a better quality door. Maybe that's why you have been in business over 30 years and he isn't.  I need the 14' door height for my base bid, however I need to quote a 16' opening as an option. Also an idea of assembly time would be nice also. I just submitted this request but noticed that I listed my home phone on 1st request as a contact. Please disregard and use the contact number listed above.

94

I received your quote on the bi-fold door. I also wanted one on a 40x14 hydraulic as well, same specs. Thank you. Are there any show specials coming up?

95

Hello Schweiss Friends; I have bought lots of doors from you in the past. I am now looking for some BIG hydraulic doors with your super Red Power pumps. How LONG can you go in an 18-20'HT door? Thanks, Jesse

96

I am quoting a bldg that has a 60x10 Hydraulic door in it. It's not a Schweiss door, but wondering if you would sell me one of your new Schweiss Red Power hydraulic pump systems for it. Can you get me a design layout with loading for us to quote?

97

Hello, I need a price for a Schweiss hydraulic door with Red Power pump and backup system. Insulated aluminum door with remote opener. Shipping to Quebec. Thank you Paully M. Project Manager

98

Hello, I would like a Schweiss hydraulic door opening 12 'high x 8'8 "wide. Specifiying your new Red Power hydraulic pump and backup system. Shipping and installation to Quebec. Thank you Roberto M., Project Manager

99

I have a customer in need of a Schweiss hydro power door with Red Power pump. Can you quote this for me? The door opening is 29'7x15 wood 6x6 post jambs with only a double 2x10 header. We have never installed a door like this, but have a lot of requests, even more since you introduced your new Red Power units. If you are interested please contact me. Our company has been in business since 1983 installing and servicing residential and commercial doors. Sincerely Vincent. Vice P.

100

I need a quote on a Schweiss hydraulic ag door. Do not know exact door measurements. It is only 30ft wide at present. Would like to widen if possible. Like the idea of different placement options for your new Red Power hydraulic pump unit. Would like to have representative come out to answer questions and give quote. Thanks, Zeke

101

This is a bid job at Inverness County Airport, specified with a Schweiss hydraulic door. Need a price please delivered to Airport, Citrus county, FL. Door must be designed to withstand 150 MPH wind load and include your new Red Power Hydraulic Pump and backup system.

102

Schweiss hydraulic door. I got a price from you recently, I need one for 49x10 (120mph) please with Red Power Electrical System and remote opener. Email Schweiss Doors quote to me.

103

Hello could you please provide further details on the range of Schweiss Red Power pump sizes and weights which each one can handle? ( smallest /largest) I am looking at several but relatively small openings for retail/commercial use. Is it possible to control the opening of multiple doors together while also having an individual control for each? I'm pretty excited about this new pump all in one unit you've developed. It was needed.

104

I have a customer that would like a price on a 30 x 17 Eave side Schweiss hydraulic door. He would also like a price on the same door for a 36 x 17. Our side wall height will be 18'6". The door, with Red Power Hydraulic pump and backup system would be shipping at the end of June or begining of July. Let me know what additional information you will need to price this out. Thanks, David

105

Sorry about the previous blank form! I've been searching for a hydraulic lift mechanism such as your new Red Power hydraulic pump with Safety Advantage System to use on residential windows in unique situations. Can you do smaller openings? I'm thinking something that's on the order of 3' wide by 5' high. Or, in another case, 6' wide by 3' high.

106

I would like prices for the Schweiss upswing hydraulic door with Red Power backup system Schweiss made. 75 x 22 70 x 21 60 x 20 to Houston Texas, 110 mph windload. Thank you, 

107

The customer is asking for an 100 X 27 Schweiss hydraulic one piece door with Red Power electric system operator. Can you make a door this large. Will one hydraulic Red power motor lift it OK? Thank you, Farley

108

Can You give me a quote for a complete one piece hydraulic lift door [including Red Power pump] with these dimensions. 28'W X 14'H

109

42 x 16 -Schweiss  hydraulic door red power 42 x 14 - hydraulic door red power not going to buy both doors. i would like to see the price difference. also can you tell me what price for a 14 x 14 hydraulic would be. all doors  / 130mph. thank you. Michail T.

110

Need quotes: 45x13/clear hydraulic door schweiss -wood building 40x18 hydraulic door by schweiss - steel.

111

email me a quote for 8 Schweiss doors for openings that are 30 x 20.5 2 doors for openings that are 41 x 20.5 hydraulic swing type door facility used for manufacturing precast concrete. Thank you Rik.

112

Compliments to you and your staff.I bought a Schweiss hydraulic 8'x34' door from you back around 1996. And it has stood up very, very, very well. Wondering now what will a new one cost for another building I am putting up. Thanks....  Bart

113

Need a Schweiss bifold or hydraulic door for a pavillion. Also, if you have a hand powered way of opening I would like to have that option.

114

needing a Schweiss door hydro fold taht is 24 wide and 15ft 11in tall ...from storm lake ia..thank you

115

I would like a quote on a 16X30 Schweiss hydraulic one piece door. It needs to be insulated.I also need some ideas how to best install this Schweiss door into our shop.

116

We had a residential project in Manila Philippines that required hyraulic door, the door should be cladded with 1" inch thick concrete to make it look the same as the concrete wall.Can you send more information and quotes on your Schweiss Hydraulic doors.

117

Would like to get a quote on two - one-piece Schweiss hydraulic doors that will go on a steel fabricated "building". Not sure what finishes are available but we would want it to match our steel sheeting or are open to options.

118

A Please quote a budget price & lead time for a One-Piece Schweiss Hydraulic Door with the following specs. 67' wide x 8' tall / include all Schweiss Doors hydraulics & controls/ for installation in Oklahoma Thanks, please call with any questions.

119

We would like a quote on single Schweiss Hydraulic or bifold door 15 tall by 24 wide. We are in southern maine and need to close the end of our open garage. My father saw your ad in Farm Show magazine. Thanks much, we look forward to hearing from you.

120

Looking to replace an existing overhead door in end of building 12'x14' Also interested in price quote on 40'x15' Schweiss bifold or hydraulic door on sidewall of building.

121

I have a door opening of 24 ft wide by 14 ft high and am wanting quote's for a Schweiss bifold or hydraulic door. Should I be considering installation of you new red Power Hydraulic pump?

122

Need a price on a 36' x 18' clear opening Schweiss Doors Hydraulic door. Will need a price installed with Red Power backup system and remote opener. Insulated. Will need the rough opening size. Will need the length of the steel on the outside and inside, for insulation and liner. Installation near your factory at Marshall, MN. If it would save me some money I can make a couple trips to pick up, but I still need Schweiss Doors to install, that way I know it's done right the first time. I'll see you at Farmfest and let you know how much I like my new door and let you buy me lunch.  :)  

123

Looking for pricing on 30' x 17' Schweiss  Hydraulic "one-piece" door and installation in Glencoe, MN

124

Hello, I am remodeling a restaurant and I would like to use your Schweiss hydraulic one piece door system for the front. I would need two one piece doors 16' wide by 9' heigh. Glass panels with a door if possible. Building is brick construction with concrete foundation. I do have a picture of the building if you like. I need a quote so I can have an idea, this way I can put a budget together. Thank you for your help.

125

need price on two doors 24ft by 18ft , Schweiss hydraulic and bi-fold and a 20ft by 18ft hydraulic and bi-fold with walk in door and windows in both

126

sorry I made a mistake on the other email address; Please some info and some pictures on the Schweiss solid hydraulic door to trent.

127

Hi, i'm interested in installing a 16 (tall)x 30 (wide) Schweiss hydraulic door. What would something like that run with a remote?

128

I'm interested to get more information regarding the Schweiss hydraulic one piece door and i would like to know if it would be possible to receive detailed drawing to understand the actual dimesion of the different components in order to understand if it could fit the design of the building. Thank you

129

Looking at general prices for a 40 x 14 foot Schweiss door. Would like prices of both the hydraulic and the bi-fold. Email will be fine since we will be away from the phone. Thanks

130

Before I order one of your Schweiss Hydraulic doors, I have not decided if door will be in end wall or side wall. Would like in side wall but that would take a big header. Any suggestions would be great. Thank you

131

Interested in a Schweiss Hydraulic Door (45'x 13' Clear) for a Client. Location: Sacramento, Ca. Please call. CFF / Roscoe 

132

We have a Customer that would like to get a quote from Schweiss Doors to install a 40'x15' high door in the endwall of a 50' building 

133

I have a client looking for a Schweiss 18'x40' hydraulic door. We are pretty new to this type of door so I would appreciate any help you can offer. We build all steel buildings in the Dakotas and may have more opportunities to package our buildings with Schweiss doors. Please call or email with info on your doors and a price quote for the 18'x40'. Thanks Roary, Watertown, SD 

134

I have a door opening. The opening size is approximately 12feet by 40 feet. I want a one piece Schweiss hydralic door. 1.A door header 2.A door 3.Schweiss Hydralic power source 4.Schweiss Hydralic cylinders 5.Shipped to Ann Arbor Michigan 20 miles west of Detroit How much would this cost me. Please break these prices down.

135

would like a estimate ona 15 ft. tall by 20 ft wide outside mount hydralic door with two windows on a steel building

136

I'm in the process of planning an airplane hangar. I will need a schweiss hydraulic lift door measuring 12 ft tall by 48 ft wide. I would like to get a quote from you asap. Wick buildings will be putting up the steel structure. Do you work with them to make sure the door matches the rest of the building?

137

We have a Model S12 #261 SN 2602 That works wonderfully. Who can I talk to about doing regular maintenance to keep my bifold door running that way? Is there an athuorized service company in Fairbanks, Ak. Thanks

138

WE BUILD POST FRAME AND STEEL BUILDINGS. MY CUSTOMER WANTS A 80X150X18 BUILDING AND WOULD LIKE 2- 30' WIDE BY 18' TALL SCHWEISS HYDRAULIC DOORS. THEY WILL BE ON THE SAME GABLE END OF BUILDING. CAN I GET THE INFORMATION AND COST OF THESE DOORS? HE DID ASK IF THE SAME OPERATION LIFT WOULD COULD POWER BOTH DOORS? I AM TO MEET WITH HIM ON TUESDAY 7/19. CALL ME IF YOU NEED. THANKS, SEAN D.

139

I have a customer that hates his sliding door and wants a new hydraulic end dr. to replace 24'x14'2" in existing shop near Ottawa, IL. Would like a price installed & Option for delivery only. Thanks, Reggie

140

I am quoting a hangar and need the design specs. for the door framing on a Hydraulic Door 80-0 x 20-0. The owner has already received a price from you for the door itself and he cannot wait for it to be installed. Please email standard details to me as soon as possible. I thank you in advance for your assistance. Shawn Richards

141

Please quote two Schweiss hydralic swing doors 18' clear height with an option for them both to be 20' clear height. Thanks

142

i have a existing building, would like a qoute of a schweiss outside mounted hydraulic door my door opening is 20 feet wide and 14 ft tall, color is white, thanks

143

I would like to speak with an engineer and a salesman to design and price a hydraulic swing door for the sidewalls in a bunker silo. I need to know about the thickest sheeting you have or if I can supply and sheet it myself and if the extra weight I put on it, will I need a bigger pump?

144

I am a general contractor looking for a quote and specs on either a 60' x 18' bi-fold or a 60' x 18' hydraulic door going to Oregon. Thanks! My client has a steel pre-engineered structure that is used mostly for implement storage. 

145

Need to know the loads of a 65'x 18' hydraulic door in new construction. Thanks for your help.

146

looking for 20 ft wide 14ft ( 13 ft 9 in) tall. very important that i lose no headroom, combine is approx. 13ft 4 in or 13ft 5 in tall not a lot of room for error. Can an outside mount accomplish this with a hydraulic schweiss door?

147

I am interested in a one piece hudraulic door and need load analysis for building engineer. Currently we are planning on a 64' by 100' building with 20' sidewalls. The walls will be 6 inch reinforced poured concrete with 12 inch by 12 inch columns on both sides of the door with a 12 inch wide by 2 foot tall header all reinforced poured concrete. We need to know if this will support the door on its own.

148

I would like the following options quoted as well: Connections to allow operation by a tractor hydraylics. Remote control. Warning devices when door is operating. Entrance lights. Note:The building is designed for hydraulic doors. Both doors will have a wainscot at 3'6", 3" of insulation and an inside liner.

149

Please price some hydraulic doors for a customer i am working with in IL. The door specs are (2)32'x16' end wall flush mount. Door will be sheeted and insulated on both sides. Please include (3)2'x3' window frame outs in each door. You are welcome to call me anytime with questions. We will install and sheet the door.

150

Please submit an estimate for the following 3 schweiss doors. Two (2) - 24' x 16' swing open door with hydraulic operators. One (1) - 16' x 16' swinging door with hydraulic operator. Please keep the 16' x 16' separate from the 24' x 16' because we're not sure if all of them need to be a hangar type. Also, We need to know structural, mechanical, electrical, and sheeting requirements. We're assuming that you would assemble the framework for the hangar doors and we would sheet and trim them out, but please confirm this.

151

There are 2 doors both are high clear electrically operated hydraulic doors. One is 36'wide x 16"high. And the other is 26'wide x 16' high. Both are on same end wall. Project is for a snow equipment storage building.

152

We are currently looking at doing a aircraft hanger for a customer near Iowa City Iowa. His building would be 50'x50'x12'. We are looking for a hydraulic door that would be 42' in length and tall enough for the 12' ceiling height in the building. Can you include a labor price for the installation also.

153

Looking to get a price quote on the freight for a 50' x 16' hydraulic door to ship from you to New Brunswick, Canada. Thank you

154

We have a customer with an opening size of 30 ' 0" wide X 8' 0" high and he has asked for an hydraulic door is this something you can help us with. Look Forward to your earliest reply.

155

We are building a new home with a sub-grade garage. We would like a garage door that can be installed with very low head room. Your hydraulic doors sound like it could be our answer. The homeowner wants to park their travel trailer in the two-car garage so we need at least a 10' tall opening at 16' wide. Thank you

156

I am contemplating a one-piece hydraulic door for the side of my post-and-beam-constructed barn. The door would be approximately 32'W x 15'H. It will be lightly insulated and faced in board and batten barn siding. Can you tell me the most cost-effective way to get this done? Thanks!

157

I have A 16ft by 32 ft opening on my tool shed. Can you fit that opening with your hydraulic doors? What is the cost?

158

Need pricing on a one piece hydraulic Schweiss  door. thinking about 48'x48' airplane hangar. Still conceptual on sixe. Just want a ball park price for options. Thanks

159

I need a price on a 64x22 one piece hydralic door. The specs on this job call for a hydraulic door or approved equal.Door speed 16-18 ft/minute. must be locked by means of hydralic cylinders, no manual latches. Emergency let-down valve. 12 volt battery backup. Must open and withstand a 50mph sustained wind. Minimum open of 18'5" x 63 feet. 220 volt single phase. Framing members with max 6' centers. Need inside liner prep, delivered to Billings, MT. Need to know approx delivery time. Would appreciate installation manual emailed to me. Thanks

160

I'm looking for a one-piece hydrolic door for my rv stall. Size is 12' wide and a minimum of 13' high. The side wall is 14' with a 2' overhang. I need as close to 13' opening as I can to give my rv enough hight to clear the door.

161

We would like to be set up as a dealer. We are a lumberyard I need a price 30x14 hydraulic door non-insulated

162

I would like to have your pricing for hydraulic bifold door Opening width : 14000mm Opening height : 10000mm Quantity: 2

163

I am considering a hangar purchase. The door header has a 14'-3" hieght and I need 14'. The existing bifold door would have to be replaced. Will a hydraulic door work? The door opening width is 54'-4". What would it cost to get a door that works to Placerville, 95667 Thanks sky

164

I am currently working on a LEED Platinum project for The Nature Conservancy in Genoa, Nevada (about 50 miles south of Reno). We have (4) 6'-6" x 8'-0" x 4 " thick doors on the north side of the building that open out on to a deck. They are shown on the left side of the north elevation I have attached.These doors are 4 " thick because we're proposing to fabricate them from SIPs (structural insulatedpanels) in order to maintain a decent insulation value due to their size and location. They weigh 3.3lb/sf which is 172# but will have a veneer and some metal trim so I'm thinking closer to 200# each.Not sure where I got the information regarding your company but I need a specification for a hydraulic opener that can handle these doors. Look forward to hearing from you.

165

I will be attending Sun and Fun on the 23rd, will you be at the show? I would like to sit down and talk hydraulic doors and what Schweiss has to offer, heard a lot good things about you guys.Thanks,

166

Could I get a quote and specs on a 36' x 18' one-piece hydraulic door? This door will be installed on the endwall of the building and will need to be prepped for an interior liner. The width of the door frame out, between columns, is 38'-5", leaving 38' as the width of the clear door opening. The door will be shipped to IN. Please let me know if you have any questions. Thank you.

167

Sir, Have an existing 90 ft X 50 ft hangar with two 40 ft doors on ramp side. These doors open to 13 ft 2 in making the hangar useless for my needs. 95% of my business is aircraft on straight floats, so basically I can't get anything in the hangar larger than a Super Cub. Price me a hydraulic door ok

168

I have a customer that is wanting a hydraulic door installed on this opening. Please advise of the cost and availability of this product.The opening size 24' wide x 14'5" tall. He would like a man door and a window in the hydraulic door. BGB will provide the labor for this job.If you have any questions please let me know. Thanks

169

I am looking for a price on a 14' x 50' hydraulic operated door. I e-mailed your company this morning. I need the price ASAP. Please call me Thanks

170

I would like to get a quote for a 36' x 16'-6" one-piece hydraulic door. 36' is the width of the door itself  the door frame out can be 36'-5". 16'-6" is the height from finished floor to the bottom of the door header.Please include:Prep for an interior liner on the door(2) 4' x 3' Window frame outs in door Remote control with one handheldDoor will be shipped to Paris, IL 61944.If you have any questions, please contact me at the number listed below or via email.Thank you!

171

Can you give me a ballpark cost for a hydraulic door to suit a hanger opening 42' 9" wide x 12' 0" high opening with 18" clear above the door. Quote complete with power pack, weather seals and safety features normally provided with a door of this type.If you have any questions [which I'm sure there will be] please call me.Best Regards,Technical Sales

172

We are interested in info and cost of hydraulic swing out door. Would ideally like a 20' wide 14' high but don't believe our building design will allow. We probably will have to settle for 18' wide. Please give me a call so we can talk through the best alternative. Thanks in advance.

173

Please quote for my customer a 14' x 42' Hydraulic door. what are the building requirments for the support of the Hy fold door. can you email me the specs. I have done door business down in the Houston area before.

174

I'm thinking about installing a hydraulic-lift door on my storage shed. I'm assuming it would be cost-prohibitive, but want to confirm before I make any final decisions. My shed is almost 5' wide and 7' tall. Can you give me a rough estimate of cost? Thank you!

175

Would like a price quote for a hydraulic door for existing building. Opening is on the interior of a wood frame machine shed so head room is limited to 16' truss height. Customer to install. Thank you

176

Hi,I need a cost of a Hydraulic door, I have a clearence of 40,14 x 12,7 Kind Regards

177

Need a quote asap complete door with hydraulics ,light weight cladding, any options such as outdoor limit switches and remotes. Need price on shipping door and time frame to build and ship.thanks Scott

178

looking for possible two one-piece doors that are at least 12' and about 40' wide in the hydraulic door design

179

I have an existing bi-fold door on our hangar that is not a Schweiss. I am looking to replace it with a Schweiss single piece hydraulic door and would like a quote on a door shipped to Anchorage. The open dimensions are 56' x 16' We are located in a remote Alaskan village. So getting the door to Port will have to be either by airplane or by barge/boat. Is it possible to have to door made for final assembly on site? I think I can get 28' x 8' or 28' x 16' sections on one of the DC-6 freight runners. Thanks, Kevin.

180

We require quote for 6 hydraulic hangar doors - sizes of doors as follows. A. Supply only B. Supply and install in Australia Type: Hydraulic Width: 18 meters Height: 5 meters Automatic operation

181

I SPOKE WITH ONE OF YOUR SALES PEOPLE YESTERDAY AND I GOT MY HYDRAULIC DOOR QUOTE, I WANTED TO MAKE SURE YOU PLAN ON SHIPPING SOON AS I AM LOOKING TO ORDER THIS DOOR. THANKS JIM

182

I would like a price on a 36' X 14'6" hydraulic door with rough outs for two 3' X 4' windows. Thanks Matt

183

Please provide quote for one(1) 35'-0" x 16'-0" hydraulic lift door with full perimeter and base seals. Quote for July shipment

184

I am interested in a Schweiss hyd door opening is 16'h 45'w please quote. We can install. Question/ do we supply the siding to cover door as well as insulation?Do the the hyd hoses come with the big door Tony

185

Can you build a hydraulic door that is 90 feet wide and 22'6" tall. I have a bifold that is 90' X 18' clear the opening is 90' X 24'. I need to get a bigger airplane into the hanger but with the bifold I can't do it. The tail height of the plane is 20' 6" or is there a way to make my current bifold door open wider. What would the price be. Thanks Brian

186

Hi; My hydraulic door I bought from you folks in 2008 Works fine. Lots of folks have admired it. My question is where can I buy more of the fine thread tek screws that you furnished? There are lots of times I need something other than regular teks or bolts for other projects I'm working on. I have been unable to find a supplier. Our local nut house guys tell me they have never seen them before Thanks John S.

187

I have an existing building with a 20 ft. wide by 16 ft. high door. I would be interested in a quote on an insulated hydralic door. Head room is a concern.

188

I am interested in purchasing a Hydraulic door from your company and was wondering how long it would take to get the door built and shipped after it is ordered

189

Hi, decided to build a aircraft hangar. Need a door to fit in with dimensions 18 meter by 6 meter hight. Hydralic or Bi-fold. Kind regards, Marten Bulling

190

Replacing 1 or 2 30x15'10" slider doors. Want no loss of headroom. Does snow concerns favor bi instead of one piece hydraulic? I like the idea of shade from one piece.

191

WE are designing and building new John Deere Dealerships. Looking a designing Hydraulic doors in the endwalls of the shop area. Looking for design information and a quote. Door to be sheeted with 2" insulated sandwich panel.

192

please provide quote and specs for bi-fold & Hydraulic doors - overall opening is 40w x 14h - this door cannot exceed 14' total height Jason

193

Request one piece hydraulic door rough quote: Hangar door opening: 44' 0" x 10' 4" 8" I-Beam door frame on "red iron" steel building.

194

We need a price on two hydraulic doors, # 1 28 ft. wide x 14 ft. high # 2 44 ft. wide x 14 ft. high Please respond by fax or e-mail.

195

Please quote me a 15'X 50' Hydrolic door , flush mount, 4 windows 30 x 40 in the door. This will be delivered to  Mt. Thanks Mark

196

I would like as much information as you can provide me about the hydraulic doors. I have a client that will need a 40' door as well as 30-32' door. I need to know the rough opening sizes, how they are installed etc. Any information that you can provide that will help the architect and engineer as well, Thanks Schweiss.

197

I am looking for a door quote on a 40x12 hydraulic bi-fold door delivered to Montana

198

RFQ for one (1) 55ft wide x 22ft high (clear opening)bi-fold or hydraulic door, FOB Calgary, Alberta Canada Budgetary priced quotation.

199

LOOKING FOR TWO HYD. 20 FEET WIDE AND 30 FEET HIGH ONE DOOR WILL BE FACEING THE SALT WATER AND WIIL OPEN ABOUT 120 DAYD PER YEAR AND THE OTHER ABOUT 60 TIMES PER YEAR I WILL HAVE HYD NEAR THE DOOR FOR A HYD. LIFT

200

I'm looking for a hydraulic system to lift our doors that we make over here in Australia, the doors weigh about 1.5 ton out on the end when fully open (there heavy due to cyclone rating requirements) therefor needing a fairly beefy ram setup. we have over forty houses to build and where looking for a supplier to jump on board.

201

I have a customer who wants the one piece hydrolic door for his ag building. I need the specs so I can load my building properly. He is looking for a 30x16 and a 24x16 both going in an endwall. I guess you can price each one for me too. Needs to be insulated. Call or email with questions. Delivered to Lake Village, AR.

202

Building a shop and was wondering what extra structural supports would be needed to put a 30' hydraulic door on the end wall. The buildind will be approx. 40'x 64' Thanks I'd also like a quote on a door 30'w x 16'h

203

Owner of Sunset Marina has advised that building is on property line & bi-fold door would encroach city property. Hydrolic door would better suit this. Please call & advise.

204

I would like a price and availability for a 40' by 10' hydraulic door. Thanks for your help.

205

NEED TO REPLACE A 27'W X 16'H DOOR ON MY BUILDING, PRICE ME A HYD. DOOR INSULATED AND INSTALLED PLEASE. TIM

206

Do you ship into Louisiana? Do the Hydraulic Doors come assembled? What is the price of a 9' x 18' Hydraulic Door with all mechanism?

207

Please provide a quotation for (4) 60 x 22 hydraulic doors for the London Joint Operations Phase 3 hangar in London KY.

208

Hi we need to get a price on a 10 x 9 Hydraulic Door.......could you let us know if we can become dealers with you and how much this type of door would be. We need the price ASAP. Thank you! Nelson

209

Hi There Wondering if you guys will be attending Oshkosh again. I have a hangar with an opening approx 94 feet 5 inches by 15 feet 1 inch in Brisbane Australia and am very keen to talk to you guys about a one piece hyd door. Look forward to your reply Regards Richard

210

Hi Please can I have a price for a Hydraulic opening door size 15 metres wide by 4 metres high, delivered to the UK. Many thanks Jez

211

WE SAW YOUR ADD ON THE INTERNET, WE ARE LOOKING FOR HYDRAULIC BI-FOLD DOORS FOR A POTATO STORAGE BUILDING. DO YOU DO BUSINESS IN SOUTHERN COLORADO? Carla

212

I'm looking for a quote on a 38'x18' one-piece hydraulic door. The door needs to be prepped for an interior liner and if you could include a remote control, that would be great. The door will be shipped to Fowler, IN 47944. Please let me know if you need any additional information in order to quote the door. Thank you! Paul

213

We are bidding two projects next week that have large hydraulic doors Knoxville, Iowa Airport - bids Sheldon, Iowa Airport. Is Schweiss quoting these two project? 

214

Hello looking for a bifold door to fit a 40' wide by 12' high building. Not looking for a fancy door, no man doors or insulation, would like to get some prices and options. I was quite interested in your 1 piece. Thanks for your time, I live in Northwestern Ontario, Canada.

215

I'd like a hydraulic door, but how can I minimize the cost? This will be for a "hangar" that already exists in my barn. The existing wooden header sags (bad "engineering" on my part 20 years ago), so I'd like to replace that with a metal beam - can that be incorporated into the design? Thanks.

216

looking for price and availability for you package hydraulic unit. Will be lifting a 42' x 14' swing out door. Completely capable of install and could put together a hyd unit but what ya'll offer is much nicer and already a complete package. LOVE IT

217

hi, i need a price on a one piece door: 18' x 8' 5 hp hydraulic motor battery backup hand crank safety sensors steel frame (painted) mounting on a concrete wall receiver with two transmitters we will cover the frame with fire treated wood. please include delivery charges with your estimate. thank you, wesley general manager

218

I need specifications to design for (2) hydraulic one-piece doors. (1) 35'-0 wide x 16'-0 centered in a 55'-0 wide endwall with a 18'-0 eave height 1/12 RS. (1) 25'-0 wide x 16'-0 high located in a sidewall with a 18'-0 eave height. Please provide me with all the dimension specs and the weight of the doors for my Engineer can design properly.

219

We are interested in Pricing and availability of your hydraulic hangar doors. (18) 48' x 20' (1) 60' x 20' (1)80' x 20' clear height. The units would be located in NE Oklahoma. We look forward to your reply, Nick

220

I need a quote and Data information for (2) 30' X 17' clear Hydro Door units. Each door will be located in one endwal at the right and left of 60'w X 100' l X 18' eh. If I need to adjust my building height please provide me the minimum require height. Thanks, 

221

My husband built an airplane hangar and door. He never finished putting in any hydraulic opener. Probably a good thing because I now see on your Schweiss web site that you have a new and improved Red Power pump.  Where do I start and who can help me in Rochester New York?

222

I am building a hanger soon and am interested in a 55'w X 14'6" tall hydraulic one piece door. Please provide a quote with basic metal siding delivery and setup. Thank you very much -Rusty

223

Would like an estimate on a hydraulic fold insulated door. 19 feet wide by 12.6 feet high.

224

We are interested in getting a materials price on one of your hydraulic doors w/ dimensions of 50'0" wide x 14'0" high to include motor operation (no clearance or obstruction problems). Just as important, if we choose to install the door ourselves, how much time and labor cost (number of men to do the job and number of days and hours to complete installation portion of the job) should we set aside. Need your materials and shipping charges, as well as manufacturing time frame and labor time and costs if we do the job, and alternatively what your labor charges would be if you do the job here in Chesapeake, VA.

225

I am going to build a hanger in Justin Tx. I need information as to cost, overhead room, side clearance on each side of door and weight of both the one piece hydraulic door and the bifold door. I want 40 foot in width and 14 foot overhead clearance when open. Will a 18 foot high side wall building be tall enough for the bifold? Are the doors delivered with external sheeting or do we use mine? Also I will need engineers drawings for my builder for strength requirments. does the door casing come with the door? Thanks Richard E.

226

I have a 8' x 16' opening and would like a quote for a hydraulic door and a bi fold door. It is a wood framed structure and delivery will be bakersfield , ca. I can still raise the beam over the door if the bi fold needs more head room Thanks Willy

227

I am getting a preliminary price for a 60' x 60' x 16' airplane hangar in Baggs WY - Carbon County. They are interested in a 50' x 12' Hydraulic door. My building supplier needs to know how much more we need to allow in his estimate to accomodate the schweiss door. This is just a starting point, but we would like to be fairly accurate in our estimate. Thanks for your help.

228

I had recieved a quote from your company several months ago for a 47 ft. wide by 18 ft. hydraulic door. Could you please requote with your best price installed, we are ready to place an order. Thank you, Tom C.

229

Interested in at least one door for a 20 ft. Wide 14 ft. tall opening. Possibly order another door for a different shed.

230

I have a Behlen slant wall quonset that I would like to put a new door on. I need your help in choosing the right door for the building. The door opening is 23'10" in width and 15'3" to the bottom of the steel header. The steel header is only 9" in width at the outside points of the opening and 13" in the middle of the opening. I need to keep the full 15'3" height of the door. Could you tell me what I have to do to mount the door and give me a quote on both hydralic and bifold doors or kits that I may need. Thank You

231

Would like a price on a 44'x18' hydraulic hangar door with remote. Will have 2.5" insulated panels for exterior skin. Weatherstrip.

232

Good Afternoon, We are about to build a new Hangar and are very interested in your Hydraulic door system.I have spoken to Dennis T. at an airport in Auckland and have seen his doors. Our hangar at this stage we,would like it to be about 25metres x 25metres x 6m high.I believe Ray J. looks after Australia and New Zealand and would love some more info on these doors before we too far down the planning trackRegards Dave W.

233

Just need a quoe on the hydraulic system with the switches and cylinders to open a door of size 20ftX7ft.

234

Please quote aircraft hydraulic door complete. The size of the door needs to be 50' wide x 18' tall. Do you have any experienced installers in this area or is this something that erects very easily with minimal adjustments? Please call with any questions.ThanksKim

235

We are looking for a isolated one piece Hydraulic Door with the Dimension 19.10m (=62,33 feet) wide and 3,50m(=9,84 feet)high for a Aircraft Hangar. The door should have a 220 V Hydraulic System and a Remote Control. The door should have also fixed isolated Windows on the whole length on the bottom half. The Door frame should be outside for a full high. Do you ship to Germany? The installation is no problem for us. If possible we are asking for your offer free our location in Germany. Many thanks for your Efforts Georg F.

236

Hi Iam looking at prices for your hdraulic doors. My opening is estimated 30'w X 14'H and One 30'X16'. Mounting style m. Man door in middle and two 36"x48" windows 6' high. Single phase 220. With a 15-20 second lift. Will these doors move up to 1'of heavy wet snow? Insulation rating up to? Thank you Todd S.

237

Need quote sent to customer directly, with a copy to myself. Hydraulic Door: 40x16 Installed by you. Power Operator Installed, Wiring by customer. Steel installed on door by you. Any questions call Steve S. Astro Buildings. Customer Bob B.

238

Hi we have a new hangar With your hydaulic Schweiss door that is Installed. Do you have any one in Boring Oregon that can come and inspect it on the Installation. This door is a Hydaulic one-piece. Thank you Joyce L.

239

I need a quote on a 30 ft. wide by 16 ft. tall hydraulic door shipping location woul be clyde ks.

240

I'm interested in your single piece hydraulic door. I also need the truss to support the door. It looks like the door hangs off the bottom of the free standing truss. So the rough opening is 12 feet high and 40 feet wide. The free standing truss would have to fit under the 12 feet high and have a deapth that would support a 40 foot door. I would want a entrance door. I would like this shipped to Ann Arbor Michigan which is 20 miles west of Detroit. Please give me a price on two small windows in that door say 2 foot by 4 foot. I will not need sheeting for the door I'll provide that. Thanks Craig S.

241

We have to replace a 40 x 14 hangar door. If you could sent us installation drawings for your hydraulic door we'd appreciate it. Cost figures wouldn't hurt. Thanks, P. R.

242

I would like to receive a quote on your new hydraulic one piece door. Door size is 15' wide x 18' tall. We have other size doors, but this is a good size to start with. We use about 30 doors per year in our construction Thanks, Dale T.

243

Hi: I've been viewing your website and have some question pertaining to your hydraulic door. How does your product attach to an existing frame? Does the current frame need to be re-inforced? If so how? What type of stress is applied to building? What is your door framing made of? How does the door come shipped? Can I arrange for picking up the door at your facility? Is there welding involved to assembly door? What is the primary differences between your hydraulic door and others on the market? The door size below is approx., should there be room allowed above the mounting area to keep the door from hitting the roof sheeting? Thanks

244

Julie I just talked to you over the phone. I need door info on your hydraulic doors 46x14 and 60x16 I need door weights and hinge info. please give me prices, If this happens it will be mid to late summer.

245

I need engineering design information for a 105-foot wide by 27-foot high one-piece hydraulic door. We are bidding on a building which has two of these doors in an endwall, and we need full information regarding the loads the doors will impose on our building, and recommended procedures for designing our building to accept the doors. Thanks for your help.

246

I was wondering what kind of estimate I could get for two single piece hydralic doors, 16 ft tall x 32 ft wide

247

I would like to add a four car garage. Each door being a standard 8x10. However, I want to install a real wood exterior to each door. I thought that the hydraulic door system might do the trick. How much?

248

For Orlando area, Fall of '09 We need a budget estimate for TWO of your one piece hydraulic doors.......sheeting will be 2" Metal Span 42". Wind speed is 110 m. p. h.........can be galvanized or primer painted............we need motorized (or your equivalent for NON manual operation). Steel jambs/"h" columns can be provided by you or our PEMB supplier (you tell me). Don R. If you can quote by next Wednesday, that will be great......please call with questions.

249

Have a old building, needs new doors. a local equipment dealer has a hydraulic door looks good. give me a call

250

I have the oppritunity to bid two hanger doors. 105" wide clear opening x 27' clear opening, with glass in door, insulated, not sure of color yet, hydraulic operated

251

I am interested in buying 2/ 9x40 hydaulic doors delivered to Grand Junction, Colo. with one man door each. I would appreciate an approximate quote by e-mail today. Thank you, Steve

252

I have a customer who is in need of a 55' x 15' one-piece hydraulic door for a hanger he is building. It will be a solid door (no windows)and mounted to steel. I need a quote that includes delivery and installation here in Sherman,TX.

253

We will be building a new subdivision with homes starting this spring. We will be using Structural Insulated Panels (SIPS)and will use the exterior wall window cutouts for interior shutters; use exterior door cutouts for doors. The garage door cutout will be approximately 16 x 7- 7.5 and with trim and outside finish will weight about 800 lbs. We are looking for system hardware and opener. One piece door would ne preferable but it could be two panels. Please have a Rep contact me. Thank you.

254

We have a fuel truck that has a rollup door on the back. We were thinking about putting a one piece swing up door onto it. Do you have doors for trucks like this? And if so, do you have any photos or literature on that type of setup? Thanks Don

255

LOOKING FOR A PRICE ON A ONE PIECE HYDRAULIC DOOR WITH ALL THINGS NEEDED INCLUDING PUMP. THE DOOR SIZE THAT I AM LOOKING IS AS FOLLOWS: 10 FT TALL, 36 FT WIDE. THANK YOU DARWIN P.

256

look at hydraulic doors.. trying to get a price.. on 10'10" high by 15'10" wide door thanks

257

I am wishing to purchase 4 hangar doors. The openings are framed with 8" steel pipe (verticle) with an overhead I beam 6" wide by 18" high. The inside dimensions are 12'high and 40' 11 1/2" wide. However, I feel the door would be best suited to be hydraulic, mounted on the top header I beam. The door then would need to be 41' 8" wide and the height would be based upon the mounting onto the I beam. This is a project I am interested in moving forward with in the near future. Please have a representative contact my cell number for further discussion. Thank you, Ted

258

Julie, Our offer is $8000 including 2 remotes. Flush mounted L door with external webbet truss with hydraulic power unit located on the right side of door when viewed from the outside facing the door. 220vac single phase motor The construction site is on a Fly-in Ranch, Fredrecksburg, TX. M. B.

259

I need a quote for a hydraulic door with a framed opening of 56'x21'. I have a meeting in the morning and i know you guys start before we do so just trying to get a jump on this. Thank you for your time.

260

Have you ever shipped doors to Australia? We're intending on putting a hydraulic door in our yet-to-be built hangar and would be interested in seeing if you can ship here, and what the cost would be.

261

I live in Oregon about 100 miles south of Portland. I would like to know the price of a 16x35 and a 16x45 hydraulic door.

262

We contacted you several weeks ago using this same formatt for a 14' x 50' hangar door bid. Are you still fabricating one piece over head doors. Aero Kinetics, Inc.

263

I am interested in a hydraulic door, one piece, for an agricultural shop. The opening will be 28' wide and the height at 14'6". I'd also like a more detailed discription of the door and what makes it work such as cylinders used, length, pump size, and how much oil is needed to operate the system? Does the door open to a full 90 degrees from the building when at it's most open position? Can the door be stopped at different heights? Are there safety stops that will hold the door when open? How do you release these stops to put the door down? How heavy is the door? Thank you.

264

Quote for 20x14' open area Hydraulic door. No sheeting. Installed and materials only prices. Delivered to Bland, VA 24315. Need quote by 12-11-2008.

265

I have a 30ft wide by 14ft high door I want to replace with a hydralic door. Please give me a installed price.

266

I have been studying your hydraulic doors and am very impressed but I want to know how big of rams you would have to use on my door it is 12' high and 17'6" wide I am concerned that I may have big bulky rams in my shop I want the dimentions of the rams and bore and stroke size to see how mutch side space I would loose. Than You

267

flush mount, 58X16, remote control, freight to zip 97211 delivery times. can you provide engineering, and drawings of door, and hydraulics.. which pump manufacturer and cylinder size are you providing. We have installed 6 of another competitors doors from Minn. and had some structure and hyd problems looking for better product.

268

I have an existing 10' X 38'8" aluminum door on my hangar that is supported and hand accuated by a a hinge mechanism attached to each side of the door. Can you supply and install the hydraulic door frame and hydraulic accuator using this door? Thank you, Gordon Z.

269

door frame and hydraulic operator 10x12 door size Flush mount type H with continuous header tube

270

Please send a quote for a one piece door to replace an existing paraport fabric door. Steel i-beam side and header. Thanks, Geoff S.

271

Looking for an estimate for a 24 X 14 1 piece door. I know there are options but give me a basic price delivered to Michigan.

272

50 wide x 16 high one-piece hydraulic (clear opening) metal sided delivered to Oroville, WA 98844

273

wE NEED A PRICE ON A 36' WIDE X 10'HIGH ONE PC HYDRAULIC DOOR, TYPE L FLUSH MOUNT...PLS INCLUDE POWER UNIT IN PRICE AND INFO ON POWER REQUIREMENTS

274

Hello I would like to get a quote on a one-piece hydraulic door with a walk door on the right side.The opening I have is 21 feet wide and 8 feet high. Also need it to hold winds of 150 m/h ???

275

I would like an estimated cost for a hydraulic door for an existing hangar with a 38' x 9.5'( -) clear opening. It would need to be mounted in front of the building which now has sliding barn type doors. Dan

276

I need a quote on a quote on a 50'x18' and a 70'x18' hydraulic overhead door. At this time the door does not need to be insulated however I may need to insulate them later. I am most interested in the one piece door. Thank you for your prompt responce, Larry

277

I am looking for a hydrolic door for my hanger that is 35' wide and only 7 ' tall. I need all the head room I can get.

278

With hydraulic doors is it okay to have people sit under the door once open for extended periods of time? How much wear and tear would this place on the hydraulics?

279

We are a manufacturer of x-ray enclosured and have a requirement for a 40ft long x 8ft high shielded door. This door must open up and shielding will weigh approx. 5000#. Would be interested in one piece hydraulic door. Please let me know if this is possible and I will provide more information. Thank you, Rob P.

280

we are working on a prototype made of container. One side of the container is supposted to be a single hydraulic door, around 2.4 m*2.4m. How big the pump for the door should be? Thanks so much

281

I have an unusual application for a one-piece hydraulic door. I have a 40' mobile machine shop and would like a price to install a one-piece hydraulic over head door. Opening dimensions of the rear of the trailer are 86" wide x 78" tall. The height can be modified by 12" more but the width can not be less as that's the inside dimensions of the trailer structural posts. Would this be an insulated door? Please contact me to discuss this project. I would bring the trailer to your location for the install. Laurence P.

282

I am looking for a 44X 14 FOOT DOOR and wouldlike a one piece hyd door so I could insulate the door. My poles are 4 2x8 nailed and glued together, and have engeered trusses 4 to 12 slope, there is a truss at the end of the building.

283

Scot; If we can guarantee a build time of two weeks we'll order a hydraulic door now. We talked this morning on the phone about it. We are pulling a trailer to the Oshkosh airshow later in July and could pick the door up on the way home from Oshkosh. I"m sure you guys are attending the show or have a vendor booth there? We would need to pick up the door on Aug 4th, a Monday.Art A. Dubois,WY

284

I am building a hanger and need a quote on two {2} hyd doors 16ft by 50ft. Please quote different methods of hanging doors.

285

We need a hangar door asap here in NW WY. We have always had bifolds but are thinking hyd one piece now. Dimensions will be roughly 14'Hx40'wide. What is the price difference? How are out is delivery on each? Art A., formerly Badger, SD. The owner knows me as I worked in a shop building bifolds in 1979 when you guys started.. we've talked and laughed at how things went. See if you can help me out quickly.. call or email. asap

286

I would like a price on a 1 piece door for a door 16' wide and an opening of 16' high when open.

287

I will be in need of a 40 wide by 11 or 12 high 1 pc hyd. door. Job location is 12 miles west of Wausau Wisconsin on Hwy 29 directly east of Mpls Minnesota.

288

Hello, I need to know about the prices of hydraulic door. The measures are 66ft x 18ft. Thank you for cooperation and your attention. Dyogo

289

price for a one piece hydraulic door - Complete exterior weather stripping frame flush mount continous heater tube 48'8" x 15'h thank you

290

I have a customer asking about a 40'0" x 11'0" hydraulic door. I have never sold any of your products yet. Can you please quote a price on said door. Please include freight to Tacoma, WA 98421. If you can provide shipping info, dims, pieces & weight soI can figure my ocean freight. If you can provide freight quote all the way to Anchorage, that would be great.

291

Hi We have built byfold doors for a hanger about 9 years ago and it is time to renew them . We have found that they were not as successfull as we thought. We are very interested in knowing about your hydrolic lift up 1 piece doors. The opening of the hanger is 15feet 1 inch high and 95 feet wide. Is it possible to have a 1 piece door of this size.If so can you help us in this matter. We have not been able to find any one here to help. Hope to talk soon. Thanks Steven W.

292

I have 2 hydro doors in this building we want to put 1 more on a end wall . you sent us a packet last week would like a price and how long for delivery thanks Rahn

293

Could you provide an estimate for a 40' x 10' hydraulic hanger door with mounting hardware and opening size. Thanks, it is for new construction. Bob Fowler

294

Dear Sir, Madame I wish to purchase a hidraulic hinge for a large garaje door. the door size is 5 meters (aprox 5.5 yds) x 3.4 meters Weight of the door is approx 350 -400 lbs. please send me a price quotation regards alex n.

295

Hi- We recently built an addition for our business and installed a small(32 x 46") door w/ hinges going into our basement space which we intend to use for storage when we move in soon. The door is relatively heavy (about 40 lbs as an oak floor serves as the top of it). It is most difficult for our female employees to use the door because of it's weight. Do you make hydraulic tubes to assist in ht opening of a door this small? If not, could you refer me to another company that dos? Thanks- Dave S.

296

Can I get a price on a one piece hydraulic hanger door foan opening 60' x 16' and 60' x 18' zip 45504

297

I would like a price quote for 2 - 20 x 40 one-piece hydraulic doors. Thank you. Steve L.

298

I would like a quote on a hydraulic hanger door. Would like a 40' x 12' door. What size opening do I need? What is the cost?

299

Could you give me a quote on the "Zero Headroom" 9'H x 24'W hydraulic doors please. How long does it take for shipping to Hawaii. Thank you. Jabez B

300

Hi Julie, Sorry I've been missing your phone calls. I've just been busy with year end and new year events. I need you to update your quote to me for a One-Piece Hydraulic Door. Here are the new dimensions: Width - 48' 1/4" ; Height - one end - 14' - other end - 13' 11 1/2". We would also like the automatic opener option with four remote controls for various aircraft. If the backup/manual door opening feature is an additional option, we need you to add that to your quote. Please email a copy of the quote. Thanks for your assistance. I look forward to visiting with you soon. Ron H.

301

I'm interested in getting a quote on 2 hydraulic One-piece door one door 20ft. wide x 14ft. tall. The other door 12ft. x 12ft. I would like them white.

302

We would like to look at the installation instructions for your one piece hydraulic door. We would also like to know about what kind of time is needed to install a 50' X 16'. We have a customer in Utah that wants to do one. Thanks, Craig

303

can you give me a estimated price on a one piece hydraulic door for my 42' wide by 12' high steel hanger. I built the hanger and have all the equiptment to do the installation of the framed door.

304

I am looking for a one piece door 30' wide 12' tall. Any info will help. also, will a door like this handle any wind when open or snow load if it snowed when open? Thanks, Dusty

305

I have a hydraulic door on a 40x60 poll building that was cought by wind I need an estimate for insurance and a New DOOR can you help me?

306

I have previously received quotes for bi-fold doors, but height restrictions and economics have led me to have to consider a hydraulic door instead. Please quote for the door suitable for 240 v with freight to New Zealand. Size is 15 m by 3.4 m

307

would like a quote on a 46ft X 14ft one-piece hydraulic door including freight. No skin or insulation. Thanks

308

I am building a 100' x 100' hangar. I am very interested in your hydraulic hangar doors. I would like the hangar door to be 70'wide x 18' high and I want it to be all insulated glass. I would like you to price the door with all the bells and whistles you have. I would also like the price to include installation. If you could email me the price quote I will contact you after I receive your quote. I would also like you to price the same type of hangar door which would be 40'wide x 10'high. Thank you ....................Robert S.

309

Please furnish a price for a Hydraulic Door, aprrox. 54'x10' delivered to my address, including any shipping costs involved. Provide a listing of any options you offer with the costs for them. Assume that I will be installing this door myself, but if possible furnish a cost to provide an installation price. An e-mail response would be most appreciated Thank You very Much, Rich k.

310

Please respond by email. I am away from the phone during most buisness hours. I need a rough quote on a 40'Wx20'H hydraulic door. Just trying to decide if I can afford to put that big of an opening in a new building we are pricing.

311

I plan to install five 60' x 20' hydraulic doors on a new hangar complex that I anm scheduled to build in the next three months. Can you price these doors to me delivered to St. Simons Island, GA? Thanks, Bill W.

312

I have a solid metal hangar whose door measures 45'W X 10'6" H. "I" beam construction. Can you give me a ball park price for a hydraulic door?

313

Would like windows in the door, and a pass through door. Need minimum height loss, so I may have to go hydraulic. I am building within the next 3 months.

314

I will be in Miami next week. Do you have any instalations of the one piece door in that area?

315

I DEAL SEC. OVERHEAD DOORS, AND AM LOOKING FOR A 0" HEADROOM DOOR. I AM WANTING TO KNOW SOME PRICES AND INFO ON THESE 1 PIECE HYDRAULIC DOORS. I HAVE A CUSTOMER THAT HAS A 24'X16' OPENING (NOT SURE ON EXACT SIZE YET)AND NO HEADROOM ,COULD I GET A QUOTE. IF I DECIDED TO GO WITH THIS DOOR I WANT TO BE SURE WE CAN HANDLE THE INSTALL. THE MORE INFO I GET THE BETTER OFF WE WILL BE. IF I LIKE THESE DOORS I WILL START TO PUSH THEM IN NEBRASKA. THANKS BIG A DOORS.

316

I would like someone to contact me by phone. My door opening is 15'-5'' wide x 11'-10'' high, now I have 5'' x 6'' post as a rough opening, will a 4 ply 2'' x 10'' header be strong enough to support an outside mount hydralic door. What additional will I need. Thank You Mike S.

317

I am looking for hydraulic hinges for floor opening to basement. Flooring is made of this man made decking. I have the door. All I need is hinges. I would very much appreciate any help I could get. Thank you Mildred L.

318

I require a quote on two hydraulic doors please: 1. 1 - 50' x 20' c/w a 3070 mandoor, and 2. 1 - 40' x 20'. Can you provide a quote for freight? Thanks, Paul D.

319

I currently own a hanger built by Bellet Construction, Jim B., that has your Bi Fold doors. I would like to change them to your Hydraulaic doors to get a greater openning height. Bellet Construction has just completed a new hanger next to mine with a door of the size I need. You may check your recoreds to see what Jim ordered, but it appears to be a 15' high by 44' length. My current hanger opening is 164" high by 44 length, so we are looking at raising the header beam that the door is attached, to accomidante the larger door. Other than that the hangers are built identical.

320

I need a quote for a hydraulic door for an opening on my steel hangar clear opening of 60ft. wide and 15ft. high. I need to purchase asap. I am a former customer. 2 years ago I bought 2 large bi-fold doors from you. thanks, call soon.

321

Need quote on extra support hydraulic door. Clear height of 19' and width of 65'. Please give budget for freight and also a install price.

322

i was wandering if you could give me a price on a hydraulic garage door for my building, i will install the door myself orif this is too small of a door to get that way or what other choices i my have for this door that you dave

323

Need price, delivery time, etc for 40 x 10 hydraulic hangar door. Square post building 40 x 40 x 10 ft high.

324

Looking for information and cost on 40 x 17 Hydro Door. The door needs to be insulated. Thanks

325

1 Piece hydraulic door with remote control. What type power-out backup system is available?

326

Could you please send me more info on Hydraulic Lift Cylinders, and how can I purchase them. Thanks.

327

I have your 60ftx16ft hydraulic door. Not installed yet. AZ hot location in summer. Page 62 says "Mobil 424 or Mobil DTE 13M (Automatic Transmission Fluid - Light weight hydraulic fluid)" Sam's club sells some hydraulic fluid without a spec. Also Dextron III. Use one of these? Or should I try to find Mobil 424 or Mobil DTE 13M? Which one and why? How many gallons of fluid do I need?

328

We have 3 doors 50 x 14 feet require to operate from one hydraulic system but individual door operation is required Door wieght 500kg per door please advice on price of the hydraulic equipment Best Regards Tony N.

329

Hi I also want to get a quote for a 55X18 One piece door (opening must be 15 High ) for a larger hanger all door have Personal Doors and must meet the florida wind loads of 100 mph Please have some call me tommorrow Thrusday Al P.

330

We are a construction company that will provide a quote to a customer for an addition to an existing building. The customer wants a one-piece hydraulic door. He would like the specs to be 44 feet wide with a clear height of 16 feet.

331

I am planning on putting up a new steel building (wood frame)in 6 or 7 months. I would like a quote for a new one piece, hydraulic door. 30'wide and 14'high.

332

Could you please send me a quote for a 10X40 one piece hydraulic door and quote the following options seperately. 1. Remote control 2. Walk through door 3. Metal siding

333

Please provide an estimate for a bifold and hydraulic one piece door for a 22 foot wide and 12 foot high opening. I'm not looking for all the bells and whistles, just a reliable and easy to use door for a machine shed. Also, give me an estimate when it would be delivered. Thank you very much. Paul K.

334

I have a customer interested in (3) 14' wide x14' high hydraulic doors. Please give me some idea on the cost including shipping to NH. I would also need to know what else I would need to purchase to make the door complete. Thank you, Mike H. Able Steel Buildings, Inc.

335

I need a 40', one piece, hydraulic door for a hanger project located near Prescott Arizona. Thanks.

336

I have a 42' wide by 10' opening wood pole hanger, I would like to put a single hydraulic door on it. What would the price be? Location is Sturgeon Bay, WI.

337

Good day to you, I am installing a garage door 14 feet wide by 8 feet high made of polycarbonate (120- 150 kg)which will also be used as a shelter/shade during rainy or hot weather. So I need to have it open by swinging up and all 8 feet of it exposed. (just like your animation door with zero headroom). Can I simply purchase the hydraulic components minus the door ? If so, how much does it cost? Thanks Philip

338

Please email me a quote for Hydraulic Door, (not Bi-fold)12'High X 16' Wide. Thanks John G.

339

Like to know what is the price for a set of hydraulic arms minus the doors for my outdoor gazebo spanning only 7.5 feet wide by 8 feet high. Thanks Philip

340

I need a quote on the following: 8 - 39 x 12 one piece hydraulic doors 2 - 42 x 12 one piece hydraulic doors 140 mph wind load, Exposure C Palm Beach County, Florida Doors to come with appropriatly designed walk doors.

341

Can supply a photograph if helpful. Hydraulic door only, must preserve header height. Would like to reuse existing (corragated galvanized / painted), siding, can that be done? Has 8x8" wood columns and 10" steel I-beam header. jlw

342

Change to Hydraulic , I have a good fab shop ready to install I live in airpark and a lot of people have gone to hydraulic I am in a rush

343

You quoted a 16X40 one piece hydrolic for me some time last year. I am finally ready to go ahead. What kind of actualy measurements do you need to proceed? George P.

344

Dear Sirs, I am going to be building a 90'w X 80'd hanger soon in Ft> Worth, TX. and I would like to see some pricing on your hydraulic fold hanger doors. Can you send me some info and pricing to the address above? Thank you in advance for your reply. Thanks again, Jeff G.

345

I WANT THE LIFT STRAPS WITH THE BI-FOLD DOOR ESTIMATE. IF ZERO CLEARANCE CAN BE ACCOMPLISHED WITH HYDRAULICS THAN I MAY GO HYDRAULIC LIFT TO SAVE IN ADDITIONAL BUILDING COST TO MAKE THE BUILDING HIGHER TO ACCOMMODATE THE HEADROOM NEEDED FOR A BI-FOLD DOOR.

346

I neeed a one piece hydraulic door. size 22 feet high, 67 feet long. I can raise the header height to 22 feet 6 inches to get the 22 feet clear. Price the door and install located in Rome GA

347

Please quote 1 piece hydraulic door. I need the headroom. 46'5" wide 12'7" high Delivered and installed @ Las Vegas, Nevada. Thanks, Jim

348

I would like a quote on a 75W X 20H hydraulic one-piece door. Please quote me on the door just being shipped to me and also a quote on Schweiss installing it in Ketchum, OK.

349

I am interested in the one piece hydraulic door of 46 ft wide by 12 ft high. Can you give me a price quote please. Thanks. Mark

350

I am looking for lift cylinders to support a hatch door to a cellar. Do you have something that would work Thanks Pat M.

351

I need a quote on a hydraulic bi-fold door. My frame around the door is 5 1/2 inch round pipe.

352

I'D LIKE THE PRICE ON A LIFT OF A 40' x 14' metal or/and wood door. THE BUILDING MAY BE CONCRETE OR WOOD

353

Just need a ballpark cost for my garage measuring 40' X 10' Am interested in the one-piece hydraulic door which I would install myself--thanks---David

354

Please quote me a price for a 42'X 14' Hydraulic one piece door including remote control and shipping to: Neil S. D. I plan to build a 50'X 50' hangar in November. I should of read the rest of your form. I haven't selected a builder yet, but have a number of quotes to select from. Steel or wood will be determin by the contractor that I select. Neil S. D.

355

I need a budget quote for a pre-hung, single piece, Hydraulically operated door.... 10 Ft. clear open height, 40 Ft. clear opening Delivered to 48166 Michigan. Thanks...

356

Please tell me how much tht hydralic byfold door in white with shippin in all would cost me the size i need is 10ft 1 by 78in thank you much

357

We have a project that I want to spec your "one piece" door for. It is an existing opening of 32'w x 14'h. What I need to know is how fast it opens/closes and what kind of cycle life it would have. This door would be opened appoximately 5 times a day.

358

looking for pricing on 12x14 hydraulic door this door would be mounted in floor (between 1st & 2nd floors) they have in place a rolling steel but are having problems

359

I am requesting pricing on two 62'x 18' Hydrolic swing doors. I would like windows with a walk door in each of the doors. I would also like an option for remote control. Thank You Scott M. Marvel Construction LLC

360

Please confirm by that hydraulic pump and controls for one piece 12' x 14' door can be mounted in less than two feet. We have quote and are ready to order

361

I would like a quote on a 45'x10' hydraulic door for the 6x6 post hangar I am building? Please include tax and shipping to my zip code. I am also interested in a quote for two hydraulic doors 14'x 9'6" that would be used on an existing agricultural building. Thanks Kim

362

We have a swing-up steel door, 8 wide X 7 high. about 300 lbs. We need hydraulics for it. Please provide a recommendation and price. Thank you. Steve H.

363

We need an 8'x7'foot door on the addition of our house. We would like to know if you can make the door white and trim it in black. We would also like it insulted. Is the remote costly? What is the difference in price between a remote and non-remote. We live in North Dakota. It is possible for us to come over and pick up the door, but wonder how much freight will be. Please E-Mail or call with this information. Your doors look like the perfect solution for us. Sincerely, Janet and George W.

364

I am interested primarily in your one piece hydraulic doors, but would also like information on bi-fold doors. At this point my primary need is marketing literature, and any digital media you may have. Especially digital pictures of your products in Ag buildings.