36: POLE BARN DOORS

1

I am designing a pole barn that is 42W x 98L and am looking for bi-fold door cost info in Minnesota. After reviewing your website I am interested in a bi-fold door that would be eve entry. What wall height is required for a 18 ft bifold door?

2

This door will be installed in a pole building 60x60 with 18ft eves. 1. Is there a minimum door column size? 2. Should there be steel attached to the building where the door rollers go up and down? If so is this provided by Schweiss? 3. can door be ordered with any door seals? Center foam cushion, side weather seals, top rubber, bottom rubber? Door to be installed in Washington.

3

Was wondering if you had any dealers in West Virginia or Virginia. I'm looking for a Bifold strap door for my pole barn build. I might be interested in your DIY kit or just purchasing a built door if there is a dealer. Thank you

4

I have a 30ft pole barn and I’m seeing if it is possible to do your schweiss style door on the pole side not the gable side.

5

I am looking for a quote on an 18'wide 14' tall bifold lift door for a pole barn. Not insulated.

6

Do you ship to our area? Looking for a garage door for our pole barn. We would need 2 doors 11x14 and 1 door 14x8. Could we get a quote for this?

7

I have a Morton building think the door is around 13.5 tall and 20ft wide wanting to not lose any headroom. thanks

8

Looking for a bi fold door for an opening approx 28’ wide by 16’ high for the front of my pole barn.

9

New construction 50 x 84 pole barn type construction, building will be fully insulated, so would be interested in a door insulation kit.

10

I am starting to redo an older pole barn with 4x6 posts, 72x36 and 8-9 feet tall. Removing rusting corrugated metal siding, leveling posts one by one and replacing bottom 4 feet of posts with concrete pillars and bolting posts with brackets to cement pillars above ground level. Will install concrete floor as next step. Then double reinforce corner posts, reinforce end rafter, with backing as shown on wood construction recommendations for bifold doors. Hoping to have a final opening of 32'0" and 9' tall, (up to bottom of ceiling rafters) Would like to add custom truss as shown in wood buildings recommendations and install a bifold exterior door that retains the full 9' opening with hinges bolted to a truss located above max opening height. vs pre-build bifold door? ((Using RAMCO panels for new siding and roof, brilliant blue and bright white that I would like to match))

11

Would like pricing for both the hydraulic and bifold door - roughly 32 ft x 14 ft. This is for a door on a pole barn. Would like windows on it. Building will be insulated at a later date.

12

Hi The company I represent is looking at providing clients with bi fold doors for their garage and pole shed. We are looking at a few companies to see if we can offer a cost effective solution while saving some money ourselves. We currently serve southern sask and have a solid client base Can you please provide some information about the perks of becoming a dealer and installer?

13

I was wondering what 2 16x24 doors would cost for a pole barn? Installation and materials cost. Thank You!

14

I would like to talk to sales about the cost of door and installation. I need to request money from state and need a rough qt for costs. the building is wooden pole building. the opening of the door in building is apx 50 by 18. I think that the new door probably should have its own frame so as not to rely on existing structure for total support. I would like to talk to sales about some of the specific requirements for my location. phone or email is acceptable thank you JS manager

15

In past got pricing from Julie and Jeremy. Need a price for a 65x18 going into a Cleary Pole Building.

16

I am in the design stage to build a pole barn I am interested in a bi-fold door Door height of 14 feet. Width of apx 45 feet. Building is 50 ft wide

17

I have a customer who is wanting a pole barn with a BiFold Door. He would like to drive in with his Combine. 60' wide X 16' tall Non-Insulated. Thanks for the help.

18

Hello I'm looking for a quote on qty3 insulated 12x10 bifold doors with operators for my 40x64 post frame shop building. With delivery to rapid City, SD 57701. Thank you!

19

I have a pole barn “carport”, poles with roof, installed on my property that was existing when we purchased 3 years ago. I would like to get a quote for installing 3 bifold doors with one man door each to enclose the structure. 2 of the doors have the similar measurements and the third door a different measurement with sloping roofline. Door 1: 36’ long x (sloping roofline from 10’8” to 9’8”) Door 2: 30’ long x 10’8” high Door 3: 30’ long x 9‘ 8” high There is an 8” fascia just under the roofline for mounting hardware.

20

have a 40x40 pole barn with 8x8 posts and wanting to get price quote on a bi fold door

21

looking to put a 16 foot tall by 30 foot wide bifold or one piece door on a lester pole building on the endwall...I am looking to build the door myself...thanks

22

Looking for a quote for a 12 ft high by 30-34 ft w opening for the gable end of a wood pole barn gable end 36 ft wide, 13-14 ft tall at the eves, 4/12 pitch roof. I want to assemble and install a kit. Width will be as much as practical to keep a 12 ft. tall opening without interfering with the gable overhang.

23

We have a barn project will a large door 42x19. Would like a quote for bifold and hydraulic door. We have plans and our permit is getting close to issuance from the county.

24

I am very interested in in your doors for a pole building that is currently under construction. I would appreciate a quote for both a bifold and hydrolic door. Additionally, due to scope creep and already being over budget I would also appreciate a quote for one of your DIY kits.

25

New 40x64x16 pole barn. Looking for insulated large door instead of conventional. Your doors look interesting. I want to make it easy to get boats, RV ect. In the building.

26

Post frame pole barn 35 x10 opening. Ideally I’d like to add my own metal siding to match structure Please send quote for Hydraulic door and Bifold door.

27

Have an existing Pole Barn (36.5 x10’) opening. Would like to talk about adding a door. Can you contact me please. Looking at spring summer of 2023 for install. Russ.

28

I have a 50 x 30 pole barn with sliding side doors on one endwall and one side wall. The approximate opening size on the endwall is 20 ft and height is about 12' I'm not sure if a bifold is reasonable to replace the hanging sliders or not. The barn is pretty standard northern MN construction, poured concrete slab and 6x4 posts 8' on the side walls and 10' on the rear endwall with free spans elsewhere. The side door is somewhat narrower, same height but I haven't measured the door opening. I move tractors in and out in the winter through this door. I am looking for two things: 1 rodent proof, 2 I plan to heat this barn so reasonable air tightness is a concern. Free span is also important. My questions are very approximate idea of cost? Is my structure strong enough to support the weight of a bifold door? How hard is it to install these doors? Would I be better off with a garage door style panel.

29

I am building a new pole barn. I am needing three doors: 35 foot by 18 foot, 30 foot by 18 foot and a 14 foot by 14 foot. Could I get a quote from Schweiss Doors?

30

Need a quote on a door. 22 foot wide 13.6 foot tall, for a pole barn. White, non insulated. No windows. Thanks

31

Hello, I am looking to get a schweiss quote on a bifold and a hydraulic door for an 18x12 pole barn opening that is a wood building/framing and also any options for the doors that are available and pricing. Thanks Zack

32

Opening on the shop Door is on eave side of building. I need maximum height for shop entrance. the door that needs to be replaced is 13' 11" in height and 19' 5" in width. We have 12" of header clearance above opening on outside of the building. This is a pole barn structure with 6" x 6" treated posts on 8' centers. I would prefer a self contained frame but can mount to building if needed.

33

I have a steel framed pole barn used for storage and I would like to install a insulated 40' door.

34

I have a pole barn type hangar. It has a barn type sliding manual door that is 40ft width by 10ft ht. I’d like to upgrade to an automatic bifold Liftstrap auto latching door preferably one that allows full height and does not add any weight to the building. I suppose a Self supporting Hydraulic door would be my choice. Also I would want professional installation. Thanks

35

Hello. I have a pole building with a 40' pole barn lift strap door opening. The current sliding doors are dragging on the floor and have never sealed at the top, resulting in a terrible bird problem. I have some experience with cable type winches, and would rather have a bifold door with straps like yours. The door opening is a custom design made from I-beams. Would it be possible to have someone come to my site for a quote or can I send photos to explain my request? The building is located near Circleville, Ohio. Thank you, Susan Stevenson

36

Looking for a door with an opening 22' wide and 14' tall, for a pole barn. This is a residential application so looking for lower end (not an air craft hanger door). What window options and general price range is available?

37

This is a new 40x50 pole barn with 6x6 wood posts set on 10' centers, steel trusses and a concrete pad and apron. It was constructed with a gable roof, so the front (and back) has that gable form. The front has a clear 40' opening with just left and right 6x6 corners. What additional support will be need to carry the load of a 36 ft. wide bifold strap door?

38

Plan to build a 10’wide door 8’tall. Remodeling a barn into a car storage building. Not worried about headroom, so I could go with a larger door. Can you quote me a 12x10 bifold barn door

39

I have a large AG building pole barn for hay and equipment. It is 106'x60'x16'. There are two framed openings for doors that are 20'x14' (maybe 20'x16'). I am interested in discussing the job with a certified Schweiss dealer / installer to include price and time line etc..... There will be two doors, one on each end as it is a drive through building. I won't need windows but would like to use your auto latch strap system.

40

I am considering a bifold strap door with windows

41

I have an existing 64 -120 pole building with a 32-18 sliding doors that I would like to replace with your bifold strap doors and automatic latching system . Looking at what options you have available .

42

I have an existing 30 x 50 pole barn that currently has a 10 x 10 overhead door, looking for an option that will allow bigger equipment to pass through to replace the existing overhead door without losing one lick of headroom.

43

I would like to get a quote on a hydraulic and a quote on a bifold strap door for a new pole barn building. The door dimensions are 18x42 feet. In addition, please provide pricing on a complete kit if I fabricated the door. I have a 46 foot gooseneck trailer that I could use to pick up at the factory, therefore please break out delivery prices.

44

Looking to get a quote for a bifold and/or a hydraulic door. The building will be a pole barn style with wood columns. Bifold door will have to have lift straps, no cables allowed on this ranch.

45

Have a 40x80 pole barn we are putting new metal on and have currently two slider doors and want to make wider with a 30x14 bifold door. Will this also require a freestanding header?

46

Email is better for questions the farmer has a pole building and would like 2 - 26'-9" x 16'-2" bi-fold strap drive-through doors 1 in each end of the building. We would like a price materials and labor as alternate we maybe able to do ourselves Job Location: Badger, MN

47

looking for price on bi fold door for my addittion this spring need 14feet high would like price for 20 24 and 28 widths can build addition to fit door it is a pole barn

48

Need a pair of 16' x 14' high bifold or like, insulated. Going onto a pole barn. Must have the automatic latching system and backup system.

49

We have a customer that would like a bifold door for a 14' wide by 15' tall opening in a existing pole barn. We are exploring options for getting them the clearance needed to pull semi trailer in, and would like pricing. Door width will be 42'

50

Have a pole building that needs new door. Would like to have a convo with salesperson to discuss options. Overhead garage door style will not work as I can’t afford to lose head room. From I can tell your bifold and hydraulic doors open to outside which is what I need. Thanks, Josh

51

I have an existing wood frame pole barn that I want to convert into a shop and am looking for a quote on a door for it. Bifold with straps. Also quote a freestanding header for it.

52

Thinking about building pole barn for the farm just checking bi fold vs overhead. Leaning strongly on a Schweiss liftstrap door model, especially since we get a lot of blowing snow here.

53

Pole barn construction. What can be considered the header, is a double 2x8 truss. Side column on building is a 2x6 wall, but I can put in any size post as required. I am interested mostly in the do it yourself one piece hydraulic door, but will also consider a bifold strap door.

54

I would like information/pricing on a 24' bifold door or a hydraulic door for a Morton pole building. Door needs to be 18' tall with remote opener and two windows.

55

this will be a pole barn monitor style with 14' eaves. i would most likely put a steel frame in for the door opening as it won't be trussed unless i'm missing something. this will be a diy project that i'll get drawn up. would plan on using 6x6 or 8x8 door side posts to attach metal frame to. total building width of 48'. looking for price quote for both bifold and single hydraulic. Would you suggest the 6x6 or 8x8s

56

Good afternoon, I have a customer that has one of your bi-fold, cable operated doors currently installed on his pole barn

57

I have a hard time hearing on the phone, but you can text me at that number. I'm looking for prices for two doors. I added the dimensions for the larger bifold strap pole barn door to the form. My shop is a pole barn, wood trusses supported by utility poles with a metal roof. I'd like the top half of the bifold door to be skinned in polycarbonate to let in natural light, the bottom in R-Panel. The West facing opening is 30'wide and 15' 1" tall. If possible I'd like to maintain a 14' clearance so a semi truck can be pulled inside. The South facing opening is 13' wide and is approxametly 14' tall (has an I-beam header). Clearance may not be an option. If you'll eMail me I can send pictures.

58

I'm looking for a 12x14 bifold pole barn door and an 8x9 door for my barn that are more architectural and are insulated. Bifold or lifting doesn't matter but looks do.

59

Need a quote on 3- 48’ x 16’ bi-fold pole barn doors with straps and auto locks. These will mounted on wood (pole barn) structure. Also, I might be building this 50’ x 100’ x 16’ hangar With all steel, so what would be the difference for mounting on a steel structure? I have an existing 40’ x 12’ bifold with cables that I would like to convert to straps.

60

Just looking for a ball park number on cost for a Glass Bifold door with straps and backup system in case my power goes out. New Pole Barn Construction. Opening will be 14' wide by 12' high. Thanks.

61

I am interested in building my own bifold door for this project and buying a kit from you. The wood pole barn has posts every 8’ down the side. My opening would be 8’ tall and 39’-6” wide but would like to have a roller on each of the 4 middle posts in addition to the two ends. The thought is this could reduce the door structural requirements. Can you tell me what is in the bifold BYOD kit and the cost?

62

I have a pole barn that has a 24 x 14 door opening. It currently has a double slider doors on it. Building is only 40' wide, so when doors are fulling slide open, the stick past the building and that doesn't work so well when windy. Sliding door also blocks my service door when open. I'd like to see about installing a bi-fold liftstrap shop door as I don't want to lose any height with an overhead door. As far as the wood vs steel building, it is wood posts/trusses/framing, but metal sided. Thanks, Lee

63

Wanted to look at a bifold strap door for my pole barn which has a 30 foot opening by 16 feet. Do you have a company close to me to give me a quote? I am located near Bowling Green Ohio.

64

I would like some price estimates for Bifold liftstrap door plans for a 28 ft wide door by 16 ft high. Going on a pole barn I'm currently construction with steel trusses. Thanks

65

Looking into building a pole barn to use as a chemical and fertilizer storage. Need a door 30 or 32 ft. wide x 16 ft. Besides your fold out door Do you have any connection or at least knowledge of hydraulic doors? Thankyou Frank

66

I plan to build a pole barn this year (hopefully). It will be a 60 X 60 building. I am wanting a 14 X 20 bi-fold door with auto latches and remote opener. I would like an estimate on the 14(tall) X 20(wide)bi-fold door. I would like a walk-in door in the bi-fold door if possible. If you have a crew who installs the doors I would like an estimate on that also. Thanks in advance Rob

67

I'm looking for a door remedy on a small pole barn. Barn walls will be 16' the width of the building 42'. I would like to install one Schweiss bifold liftstrap door of 36' wide, I need to assure at least a 14' head clearance. I will want an automatic & remote lift/lower. What do you have that will help me finish my plans? 

68

Looking to get structural information for a 30'x16' one-piece hydraulic door for the eave side of a pole barn. the building is 18' from floor to ceiling.

69

I am planning a 26' x 34' Pole Barn that will have a 14' x 14' Door opening. I am interested in a Quote for a Bi-Fold Door, please include shipping cost to the Seattle area.

70

Hello - We plan on building a metal pole barn on our property and would like to give it a hangar feeling, and match our "Modern Farmhouse". Could you provide a budget a 42' wide bifold door, both in traditional siding (or maybe the barn builder provides the siding) and a more contemporary glass looking finish (like a glass garage door seen at a bar, etc?) Hope that info makes sense. Thanks - Mike

71

I'd like to get a quote on this bifold door. Planning a new pole barn shop and would like to have a full width door on one section of shop. May want a man door installed in it but definitely a window or two. Also do you have any installers in my region?

72

I have a pole barn that I would like to put a door on the center bay. It is 23ft. wide and 12 ft. height

73

Would like estimate on a 14 ft x 14 ft lift strap Bifold door for a pole barn.

74

I have a pole barn. I use it to store top soil.looking for a door used mainly to stop wind, rain, sun, need to be able to open or close as needed. I might be interested in Two doors for each end of building.

75

I have a 36 X 60 foot pole barn with 60 ft wide standard trusses and 14.5 inch walls that I would like to store my Super Cub in. First, do you install your doors out here? Second, can you recommend a safe bifold door size? And, finally, can you send a quote? Thanks, Stanley

76

I am building a 50' x 60' pole barn with 20 foot ceiling. I would like the largest bifold door that will fit but remain cost-efficient. What do you recommend? Thanks!

77

Hello, I have an existing pole barn, it is 100'x 50' with 30' extension "wings", and I am wanting to eventually convert some of the space into a 60' x 50' enclosed aircraft hangar with a large hanger-type bifold strap door. I'm looking to get in contact with someone who could maybe help me with whether the structure I have currently would be able to support the weight of a large door and what kind of price I would be looking at for purchase and installation. Basically the opening I would like to fit the door in is 49' 1" wide and 14" 10' tall, the vertical poles seem to be 4 or 5 inch steel pipe, and the trusses are made from what appears to be 2-3 inch steel pipe. Would love to talk to someone who could tell me whether this is a feasible endeavor!

78

WE ARE DESIGNING A WOOD POLE BARN WITH METAL SIDING AND ROOF. THE SPACE WILL BE CLASS II, DIVISION 1 (COMBUSTIBLE DUST) WE PLAN ON 2 BIFOLD DOORS ON END WALLS. ONE WILL BE 14' X 14' AND ONE WILL BE 26' X 14'. THE WOOD TRUSSES WILL BE 8'-0" ON CENTER. CAN YOU PROVIDE ANY DETAILS FOR BRACING AND PRICING? THE POLE BARN BIFOLD DOOR PROJECT IS IN COLUMBUS, OHIO.

79

Wanting to have a quote. It's a pole barn built out of wood but covered in metal. I wasn't sure what you called a metal or wood building. I have two other doors next to each other. They are 18'0"wide and 10'0"tall. I'd like a quote for these also with the hydraulic doors. Can these two share the same controller? Thanks Lynal

80

WOULD LIKE AN ESTAMATE ON A HYDRAULIC DOOR UNIT - 30' WIDE BY 16' TALL, WILL BE INSTALLED IN A POLE BARN WOOD CONSTRUCTION TYPE BUILDING 18' CEILING HEIGHT (ADVISE IF HEIGHT OK), COLUMNS ARE TO BE 3 PLY 2X6 LAMINATED

81

I am looking for a quote on a Bi-fold door shipped to Sudlersville, MD. The door will be 40' wide x 16' tall, installed on the gable end of a 60' wide x 20' tall wood frame pole building. We bought a similar door from you in 2012.  Thank You, Leroy C.

82

I am looking to put a bi-fold door in a wood pole barn. The barn will have a 60' wide, 150' long, and be 20' tall. The bi-fold door will need to be 30' wide by 20' tall. The building is in Clayton, NY.

83

Have an existing pole barn, I'm thinking the one-piece hydraulic door would not lower the opening, however like the recessed version but realize that's going to lower my opening height, by about how much ?

84

Can you give me the best options for closing in my pole barn. I have a 40' x 14' opening but need to be able to open all the way, and I think a one-piece hydraulic door would be best for a hay squeeze and motorhome. Need ASAP

85

Do you have someone that can come look at my building and give me the best options for closing in my pole barn. I have a 40 x 14 opening but need to be able to open all the way for a hay squeeze and motorhome, so I was thinking of using a hydraulic barn door, but I'm not certain. Need ASAP

86

Request a price quote for a strap lift bifold pole barn door 37 ft wide, 12 ft high to install on my pole barn. I intend to convert the structure from a 20 ft wide, two section rolling door to the bifold door to accomodate my airplane. Reply by phone or email is acceptable.

87

Have a pole barn 35x75. Poles are 15' on center but wandering if I could put a bifold pole barn strap door to cover the whole side. 75'. 17-18' high

88

Looking to add a bifold liftstrap hanger door to the gabel side of my pole barn. need a 42 foot for wingspan and 13 for height. ceiling height in barn is 14 feet and side of barn is 56 feet

89

just wondering what a 30 x 12 machine shed door costs. Older 6x6 pole barn shed Sliding doors on it now, want bifold pole barn doors.

90

Building a pole barn for ultralite aircraft storage in IL. Need a clear opening of 32' wide and 10' high. How much would one or your bifold or hydraulic doors cost for this application?

91

I have an existing pole barn style livestock building in MT. I really would like a door from you since the pole shed currently does not have a door. I would like a full quote for an installed hydraulic or bifold pole barn door. Door is 40 x 16

92

Need estimate on hydraulic pole barn door. Will need 2 side by side one piece doors on the sidewall of building. 34'10" wide x 16' tall, for a pole barn. Door header is steel I beam for both doors, center (in between 2 doors) has 16" wide steel I beam for post, other 2 side posts are wood. Will one of your new Schweiss pumps operate both of these doors.

93

Need a price for a Schweiss verticle lift bifold strap door with remote door opener and walk door. The opening is 30' wide and 16' tall. We're putting 24 gauge pole barn metal on door. 

94

I am needing a genetic seed industry door with 14' ceiling. Want a Schweiss bifold liftstrap door with autolatches on the gable end 24 ft wide wood building door able to use as much of 14' tall door opening  as possible.

95

Do you work with Do It Yourself door projects? I am wanting to build a 24' wide Pole Barn door for my RV. Looking at 24'x40' with a bifold liftstrap door on end wall. Wall height is 12' with 4:12 pitch roof. What is the overall door height for a 20' wide RV garage door to get a 12' opening height? Do I need a 18' wide RV door for more header space? Price difference for a flush mount door vs a face mount door? I am interested in a bifold door with a manual door latch for the lift-straps. 

96

Quote a Schweiss pole barn door, 40 by 11 foot bifold opening with straps. This is a pole barn hanger door and ready for the door installation as soon as you can get manufactured door to me.

97

I am just looking at all options for a metal pole barn replacement door. Presently has a sliding door on it. I need to keep the height and as much width as possible. An overhead door will drop the door height down a foot. That won't work to pull my camper in. Someone mentioned for me to check into Schweiss hangar doors for no loss of head room. About 12 ft 10 inches wide and about 11 ft 7 inches tall is the door opening I need to have.

98

I would like information and pricing on 34x16 Schweiss liftstrap bifold door. This would go in an insulated pole shed building.

99

Retrofitting wood pole bldg hangar. Existing door is vertical sectional type with tracks that run across the opening and inside of and parallel to the sidewalls. Would like to place a Schweiss bi-fold with lift straps on it now. How soon could you deliver?

100

Hello I Am building a polebarn for an airplane hanger with a 65' x 16' bifold door, And the homeowner wants me to put in steel columns on the sides of the opening. Could someone email me and let me know what size we should go on that? Would a freestanding header work for this? Should we go with an I- beam or a steel tube? I will also have some more questions. 

101

My building is in the planning stage. Need pricing and recommendations. I am looking at a 60X60 building of poll type construction. I marked the form for a 58' bifold Schweiss Liftstrap door, but that is just a guess at this point. Should I go full with of building? Thanks, Rob

102

I am eventually going to need 4 doors 20' wide x 14' high. I cannot spare any headroom. I would like to start with one door and see how well it works for me. The building is a 60x100 pole barn, recently concreted inside, with 14' of clearance. Unfortunately the doors cannot go on the gable end. (not enough room to road). Give me price on which ever door gives me most headroom

103

I have a pole barn that I would like. To put a door on and like the idea of a bifold size of opening is 25 wide by 18 high. Include patented lift straps, insulated, free standing header.

104

I have just finished building a pole barn. I am inquiring about a hanger style bi fold lift strap door. The size is approx 40 foot wide x 16 high. What would a ball park price be on something like this?

105

I have to quote a pole barn, 80' x200'x25', for boat storage, need to get a quote on 2- 40'x23' bifold liftstrap, or hydraulic doors, barn won't be heated, but I would like the doors at least lightly insulated and able to seal tight to keep all rodents out during the winter months. The job is near Rochester ,NY.

106

My pole barn has a homemade wooden bifold door that has been in place for 12 years but has reached the end of its useful life. It never really sealed properly but has otherwise been satisfactory. Before rebuilding this door I figured I might as well find out what it would cost to replace it with a factory built bifold or one piece door.My building has only a single end truss and no extra bracing but was designed with the 45'X 11'clearspan opening and has had no issues caused by the weight/stress of the present door.I am guessing that either of your doors will weigh more than my wooden door and I may need to modify my structure to accomodate your door. Which of your door systems would be most suitable for my building with the least amount of modification to the building itself? Please note that the dimensions I have supplied are approximate and I will supply exact dimensions if I proceed with the purchase. Your door looks 100 times sturdier than the old clunker I have on it now. Thanks.

107

Building was built this summer, has sliding doors now, don't ask me why, it should have been fitted with a bifold lift strap door. This is on a pole shed building, poles are set in white rock, there is no concrete in this building. Is the quote installed price? I also have a shop building with a 14 foot by 12 foot 4 inch height I am interested in putting your door in. It is an older wood building with steel siding. Has a foundation and floor is concreted. Do you know anybody who wants a sliding door, still in good condition?

108

Currently have end slide doors. Building is pole barn construction with metal sides and roof. Interested in your design for easy opening,sealing and height restrictions in other designs. This lousy, hard to open in the winter, sliding door will be used for a bonfire on Halloween, so please rush your order if at all possible. What other info do you want me to get to you?

109

We are looking at building a new pole barn on our farm. We are very interested in the Schweiss bifold style doors. Need info for the structural load and engineering data for building our building with your door. Also need prices on the doors. The end wall is going to be 40ft wide and 20 tall. We would like to do 2 18ft by 16ft doors if that is possible with these. If other doors (hydraulic) would be better please feel free to suggest that also. We do want these doors to be able to be remotely operated from inside equipment also. Appreciate any literature, suggestions, and data that you can send us. Thank you very much for your time and info.

110

Need a bifold door for a lean to build on side of my pole building. 32'x9'high. What would be most cost effective? Will for sure want your lift straps and auto latches. Upper Michigan, don't forget to insulate.

111

This is an existing pole barn, 40X60. Would like to put bifold door on gabled end. What size header is required, 2X10,2X12 ect? How much shipping could I save on factory pickup? Shipping weight? R factor on typical bifold door? Thanks, Jason

112

We have a barn/hanger with a door opening of approximately 40 ft. wide x 16 ft high and would like to install a bifold hanger door if possible. The building is a pole barn structure with a heavy glue Lam beam header over the door opening. Questions: 1. Do you have a rep in our area who can check out our building to determine if such an installation is possible and what exact size we need? 2. Are their installers in our area who are experienced in installing your doors and who could install ours? 3. What would be the approximate cost of such a door with lift straps? Installation? 4. What exact information would you need to build us a door that will fit our building structure and opening? 5. What other questions should we have ask?? Appreciate you help. Thanks Wilson

113

Looking for a quote to replace a door with a bi-fold door.  The rough opening is 19 high and 48 wide. wood post construction, similar to a pole barn construction. Lift straps please, and moderatly insulated.

114

I have a 50x50 pole barn that I would like to put a bi-fold type door on. The end walls are 12' tall. Can you provide a quote for various widths from 32' wide to the max width of 50'? I am looking for the most economical option and I will have to have your installation crew install in Georgia. How much more for a wind-rated door?  Thanks, Mel.

115

I would like to get a quote on a Hydraulic and Bifold Door I have a pole barn and the door opening is 28' wide and 13'6" high. Delivered or installed by Schweiss to Louisiana. How soon?  Thanks Bill

116

Thoughts and prices on 16ft tall x 22 and 16 x 40 Schweiss bifold door for pole barn- do I need suport frame? Do you recommend lift straps over cables? Thank you Harry

117

I am looking into building a new 48 foot wide pole building with an 18 foot ceiling. I would like a quote for a 36 foot Schweiss bifold insulated door. Put 2 small windows in the door.

118

I require an approx. price on a 12'H x 22' wide bifold door that I want to put on an existing 6"x6" built pole shed. I will be able to make the door opening match what the Schweiss door will require.I want this door to have lift straps.

119

Seeking a quote for a pole barn constructed Hangar. Not sure the Schweiss bifold door location can be considered end or side wall as the structure has a roof with fall away from the door opening. Give me some professional Schweiss Doors input. You know doors like the back of your hand. Thanks

120

I need a 40 X 10 Schweiss Bifold door with lift straps for a pole type building. Should have top override jiggle and remote opener. Could you provide a quote please? Thanks Tony

121

Gentlemen: I have a 40 x 60 pole barn with 14 foot walls and a 20 foot wide sliding door on one end. I intend to pour concrete and turn it into a shop. With  14 foot walls, I can't afford to lose any height for an overhead door or bi-fold. I've heard a lot about your quality Schweiss hydraulic / bifold doors. Could you give me a cost estimate. I would like to intall it myself, but need to know if I have to reinforce my building. Can my wood pole building support your bifold doors. Thanks for your help.

122

Price the following: 16' tall X 30' wide - It will be placed in an endwall. Please price Schweiss hydro and bi-fold doors. We don't know yet if we are  going to build a steel frame or a pole barn, please take this into consideration.

123

Does Schweiss Doors make screen doors for pole barns. We are located in SE Wisconsin. Thank you,

124

Recently built a 30 x50 pole barn =, and considering what kind of Schweiss door to put on the end. Interested in a bi-fold door, approx. 20' wide x 12' tall. It looks like to me you sell the frame and I would cover it with what I choose, is that right. Could you send me some info on how much, and other relevant info on your product.

125

I'm building a pole barn and I'm considering a Schweiss bi-fold door for one or both of my shop doors. We're considering 24 and 32 wide doors that are 15 feet tall. The 32 foot door is in the end wall, and the 24 foot door is in the side wall. We are building this winter or next spring. Could you send me a quote?

126

Putting up a 60 x 200 pole barn. Need a door on the end. Please provide a price so I can compare bi fold and hydraulic doors, and also so I can compare to what the contractor is offering. Door will be 18 high by 50 wide. Thanks!

127

WE ARE CONSIDERING BUILDING A POLE TYPE BUILDING IN WASHINGTON COUNTY COLORADO TO HOUSE FARM MACHINERY USED IN THE OPERATION OF A DRYLAND WHEAT FARM AND TO HOUSE A SMALL AIRPLANE USED TO TRAVEL FROM OUR MID NEBRASKA RANCH TO THIS FARM. WE WOULD LIKE TO KNOW IF A BIFOLD DOOR OR A HYDRAULIC 40 X 14 DOOR WOULD BE RECOMMENDED FOR INSTALLATION IN A POLE TYPE BUILDING WITH A 50 FOOT WIDTH AND THE APPROXIMATE PRICE WE SHOULD ALLOW FOR THIS IN OUR ESTIMATE OF COST CALCULATIONS. THANK YOU

128

Looking into the possibility of installing a bi-fold door in a machine shop. The construction is simular to a pole building.

129

Have a steel pole barn with 14' walls the door way now is 16'x12' tall i need another 1 1/2' in height to fit new motorhome in. Which Schweiss door will give me the most head room, the vertical lift system of the hydraulic swinging doors 

130

Looking at a schweiss bi-fold door for a pole barn. Height-12ft, Width-12ft. Options: Lift straps. auto lathces, safety equiptment (sensors). Let me know price range and door sizes if this is not in your range.  thanks

131

Hi I am bidding a 40x60x20 pole barn, and would like a quote on 30x20 bifold door centered on the gable end. also tell me what lengths of steel I need for the door. thank you

132

I have a pole building 60 x 80 and I'd like to replace the sliding doors on the end of the building with Schweiss Bifold Doors. The opening is 14 x 28 and I'd like to lose no clearance if that is possible. Thanks

133

Need price a hydraulic single door 25X16ft pole barn. Just door and cylinders,I well furnish power unit.

134

FYI, I am bidding a 40x60x14' pole barn style building and need a estimate for a bifold door. What size would you recomend for this size building? Thanks

135

Pole barn Door. 32x16. Gable end. You install door and metal. Bifold Straps. Install at Nebraska  Who pays sales tax. What are the options for insulation

136

I am looking at retrofitting my existing pole barn and am interested in putting a bifold door on an opening that measures approximately 10' wide X 9' high. How much clearance would I need above this opening. Can you supply a door for this size opening and can you give me a "ballpark" price range so that I can tell if it is a feasible consideration.Thanks for your help,

137

I am building a new pole building. I am interesting in an estimate for a 20x14' door (end wall) and 24'x14' door (side wall). Right now I am looking at constructing a 16' high building to clear for overhead bifold doors, but may be able to lower the building height with your doors. Also, I may be interested in wider doors depending on the difference in price. I am interested in an installed price and material only price. What are the insulation options? Is the building steel installed onto the doors?

138

I am building a hangar/barn combination. I need a clear space of 40x15 to accommodate my airplane. I am planning on a rough opening of 48x16. Is this sufficient? What door do you recommend, bifold or hydraulic? When is your next delivery schedule to Alaska? Regards

139

Looking for specifications, loads and reactions for the hydraulic door specified below. Building/hangar will be pole-barn construction with truss roof. Steel I beam columns and header can be used if necessary for the door. Door is in non-bearing end wall.

140

I have 40 X 60 polebarn with concrete floor, currently has 2 sliding doors. End wall door opening measures 13-6 tall and 19-5 wide. Side wall door opening measures 12-7 tall and 22 wide. Would like quote on hydraulic doors for both sizes and quote on bifold doors for both sides. Please contact me on my cell phone if any questions. Thank you.

141

we are working on a pole building to make into a shop we needed a price for a bifold 24'x14' the buildig has 16' side walls we are going to use for truck parking thank you S

142

I have 2 very large pole barns that I keep my equipment in recently built. Right now I have canvas door with like a belt belt buckle strap. I am looking to put a sturdier bifold door like you offer because I can't lose any of the width room. I am not so worried of the head room rather the width of the door.

143

I'm currently building a pole barn and looking for options for a large hydraulic door (14'X20'). Do you service this size door? If so what are your prices?

144

We have a customer who is interested in a bifold door.This door is being installed on a large pole barn. I will give you the specifications and if you are interested in quoting this door to us or you have any questions please contact me. Thank You. Gary (1) 24'0" WIDE X 13'8" HIGH. A. Wood jambs B. Standard pole barn steel siding to be applied to the face of the door by the contractor. C.Motor operated (115v)1ph

145

Hangar is pre-existing with sliding end doors on both ends. Wood "pole-barn" construction. Photos available of inside of building showing construction. Depending on price, I am interested in 1 or possibly 2 bifold doors. Exact door size will have to be measured but measurements below are close. Concrete floor. 40x60 hangar with 20x60 lean-to down one side.

146

I am desiging a new farm shop to be built this fall. Most likely it will be pole barn type construction but I am also considering all steel. Will be needing a sturdy hydraulic door.

147

Please answer the following questions: What is the R value? Can I get four remotes? Do I need to do any structural improvements to my pole barn style farm shop? It has double 6x6 posts on either side of the door already. Will the bifold door open slightly more than horizontal if I need it to?

148

I need an estimate for the door complete with actuator,remote control,lift straps,all mounting hardwear and shipping cost. We will sheet and insulate the door with our own materials. The building will be a pole barn type of structure. Construction has not started yet and we would be interested in any information on how to properly strengthen the building to accommodate the extra loads. Thank you

149

I will be putting up a pole barn with 1 bifold door. The door will be installed on one of the ends. I would like to get a quote on an aluminum bifold door 44' wide & 17" high with the automatic latch option and radio control option included. The door will be for a work shop.

150

Hi my name is Steve and I have a shell up for a 60 x 60 hanger. I am looking to put a hydraulic 14' x 60' door on it. It is a wood pole barn style building, and at this time I just have gravel floor. I would like to put the door on now and do the concrete next summer. Is that possible? Could you send me a bid for a 14' x 60' door? Thanks, Steve

151

I am looking to get a quote for a 18' x 40' bi-fold door. I am in the process of starting construction on a new pole barn that is 66' x 120', I want to put a door in the gable end. Let me know what other information you may need. Scott

152

I am interested in a Bifold door. This will be for my pole barn and the opening needs to be 13.5X40. Can you give me any advise on construction and building requirements? Also I need the cost to ship and the cost of the door and motor and ect. Thanks John

153

I Have a Pole building with 2 14'X14' openings with a man door in between.I saw one of your photos that had a door where the top half was a bifold and the lower half swung out sideways. Right now I am exploring my door options and am interested in any information. Is it possible to turn the front opening into one wide door. Or does a door that large mean reinforcing the building.

154

I need the technical data for a door, dimensions 42x12. Loading pressures, bearing points, framing requirements. The purpose is for including in a building quote. Building type is pole construction. We intend to truss end the endwall, and we will need the loading specs so we can accurately quote the customer the building. Our quote may include your hydraulic door quote.

155

I'm looking for a quote for the frame/hardware for a 24' wide, 12' high bifold door for my pole barn.

156

I need to know if you can fit a 15'x24' bi-fold door in the end of a pole barn with 14' walls that has a vaulted ceiling. I want the door to have a 20' hinge with 45 corners. Will it miss the over hang of the barn which is a 2x6 fascia and the roof ptich is a 4/12

157

We have a pole barn that is 2 years old. We use this for storage of our business equipment. I would like a quote for a 20x12 bifold door. Also do you provide financing? Please contact me via cell phone or email. Thanks

158

I'm interested in getting a quote on a hydraulic door. My building is a pole barn. The rough opening is 38'-6-0". This is an existing building that will need a new door.

159

I am building a pole barn 40ft x 60ft. I had planned on 3 20ft slideing doors and due to cost I most likely will do that. I would be interested in getting a price on 3 20ft x 14 ft doors. I have a center pole at each end. Your doors look great but I am afraid they are out of my price range.

160

I am building a wood pole barn for my Cessna 175 airplane and would like a bi-fold door. Outside dimension will be 42'. What size post do I need at the corners? Are there any structural requirements for the opening header above the door? Are there any other structural considerations needed for your door? What electrical requirements 110v or 220v? Is there wireless remote control to operate the door? Thanks, Andy

161

I have a polebarn/hanger that I want to put a bifold door into. My end of the hanger is 32 feet wide by 12 foot high. What would be my cost and specs for the door?

162

Have an existing 40 x 60 pole barn I need to add a door on the end with a 12' vertical opening for a helicopter. Looking for a suggestion and quote. I bought my last door from you. Thanks Jeff T.

163

Hi, we had a trailer display next door to one of yours at Oshkosh this last summer. I was talking to one of your rep's about your doors. I have a 40'x60'x12' pole barn that has two doors on the gable end. One 12' overhead and one 16' slider, with approx.10' of wall to seperate. The door that I would need would be 12'x38'. The attachment posts are 8"x8"on the sides. I would need a strong new header once the wall came out. Give me an idea of what it would take to convert this barn to one of your doors. Thanks, Randy

164

I have a pole barn with a door of 23' 5.25" Need a price on a door or a dealer in my area. Thanks Jed

165

Dear Mr/Ms I am a student at Niagara College, We are designing light airplane hangar for a client. We are interested in a bifold door and the opening is 30' x 10' and the building is pole barn construction. I need to get some information on the bi fold door. I will need to know the weight of the door so i would be able to calculate the size of beam and columns i would have to use, how do i attach the door to the beam and any recommendations that you may have. Any help would be greatly appreciated Best Regards Brian M.

166

This is a pole barn construction with iron clad covering Door opening must be maintain full size. This means a bi-fold will have to mount up on the gable. And the hydraulic one piece as high as possible. No sheeting or insulation needed. 220 volt OK

167

Hi,I have a pole barn with two door openings 10ft wide by 9ft high. Do you offer a bifold door for this size? Thanks Bill

168

I would like to price a 25 ft widw by 16 ft high door for a pole barn for ag use. Would like the price of a walk in door in the big door

169

I have a Pole Barn style building with sliding doors at each end. I want to change them to one piece hydraulic. Thanks, Darren

170

Hi - I have a newer pole barn with 20'W x 14'H sliding double door. I would like to know the approx cost to convert this to a bi-fold. Could you give me a call on my cell phone for discussion? Thanks - Sheldon S. Cologne, MN

171

I am working on putting together a shop and am looking for door cost. I am look to put in a 30x16 and a 14x16 the large door would have a man door and both would have some windows. What would doors like this cost and what kind of framing would need to be done on a pole barn? The poles would be 8x8. Thank you Leonard A.

172

Looking at pricing for a door to replace double slider on my pole barn. Will have to have the ability to be insulated.

173

I have not installed any framing for this door yet. It's on the gable end of a pole barn with a ceiling hieght of 16'.

174

I am building a Pole Barn with OSB sheeting and vinyl siding. A buddy and I were talking tonight and thought, "why not make a bi-fold door like the hanger?" My current rough opening is 16'3" wide and something like 122 inches high. If I put the Bi-fold on the outside, I could hing up higher so the bottom of the door comes up to the full height of the bottom of the rafters. Can we talk about this? Mike H.

175

I am currently planning a large utility building. I would like to have a 40' X 14' door for equipment access. Pole Barn is 40'X60X16'. I am looking for a price and information for the barn company. John Y.

176

looking for bifold 45 x 12 with electric operator installing on wood pole barn please give me a price with approximate freight to zip code above

177

Need a price quote for a Bi-Fold Door. Price should include installation of door and istallation of steel door sheeting suppied by us. Proposed building is aprox. 12 miles north of Park Rapids, MN. Door will not be insulated. The building will be a post frame "pole barn ".

178

I'm interested in an estimate for a bi-fold door for my pole barn. The opening is roughly 12' tall by 20' wide. I'll want the door insulated, and please include the opener and all hardware needed to install. Also, can you estimate installation time? Thanks, Roger M.

179

buildng a pole barn hangar. Rough opening 40 wide by 16 high. need quote on bi-fold door with straps. need door to billings mt by august.

180

I plan on building this fall/winter. I have been looking at both wood pole barn structure and all metal buildings. Still weighing my options. I would like door size to anywhere from 28-36 feet. Where are price increases? Would be installing myself and there might be 2 of my neighbors putting up buildings at the same time. We are going to shop for buildings the same way.

181

The barn that this door would be installed on was origanally designed for a bi-fold door quoted by your company. So structually the pole barn in question was designed and preped for a bifold door of this size.

182

Would like cost for doors with install for 1. 41.5 foot Bi-fold 2. 41.5 foot Hydraulic Buildings will be of pole barn construction metal siding with shingled roof. 48 foot by 48 foot with 14 foot eave height. Doors will be installed on the non load bearing wall. If you need further info please contact me at the above phone or e-mail me. Thank you Randall S.

183

If we put up a 40 x 40 ft pole building with 6x6 beams 8 ft on center would it be possible for a 40 ft non insulated bi-fold door to be put in? Were using enginered trusses for the roof and I was wondering the price on the widest door I could put on this barn.

184

I have a shop 72'x36' with 14' eaves. It has three doors on a side wall. Pole construction with a concrete floor. Two doors are 12x 14 on each end of the sidewall and a center door is 24x 14. each of the doors are framed with 6x6 poles. The center door has a laminated header.

185

what is the $ for a hydro door 40 Ft? are they cheaper compared to the bifold or equal in $. 40* 50 pole Barn thank You Bryan P.

186

Thinking about building a hanger. 34x36 pole barn with a 12ft high door probably 32 ft long. Don't really have any idea of price, looking for ballpark figure. Understand yours is a quality unit. Thanks Alan H.

187

I am planning on building a 60X60 pole barn type hangar and wondered what you would suggest for a door. I already have a 42' door of yours and have enjoyed it. What are the costs and what would be the shipping to Bozeman, Montana?

188

WE DO SMALLER DOORS. I HAVE A CUSTOMER THAT WANTS A 36 X 15 INSULATED DOOR. IT NEEDS TO BE BIG ENOUGH TO GET A COMBINE IN WITHOUT TAKING OFF THE HEAD. WE MAY HAVE OTHER APPLICATIONS IN THE FUTURE. I AM WORKING WITH A BUILDER THAT HAS GONE INTO POLE BARNS AND OTHER TYPES OF BUILDINGS. LET ME KNOW WHAT YOU NEED TO QUOTE A PRICE. THANK YOU NORMAN F.

189

NEW HANGER CONSTRUCTED IN WOODRUFF, WI. THE HANGER IS POLE BARN CONSTRUCTED WITH STEEL. DIM. ARE 60X60X17'. THE DOOR SIZE WILL BE 54'X 16'. THE DOOR WILL BE THE BIFOLD W/ STRAPS. MANUAL LATCH. TOP AND BOTTOM RUBBER, COLD WEATHER PACKAGE. CAN IT COME INSULATED? IF SO PLEASE QUOTE. I'M PUTTING PRICES TOGETHER. WILL START SOMETIME THIS LATE SPRING, EARLY SUMMER. THANKS, TODD

190

Hello, I saw your doors at the state fair a long time ago (1991) I just ran across your flier and thought I'd give you a call. I have a 10'x10' opening on my pole barn, it has a slide by now but would like a door like you build with the split in the middle. If I could get a price for that and maybe inquire about just buying the hardware and opener, I weld and thought it would be fun to build my own door frame and sheeting. If this is possible could I get prices for both? I do like the yellow straps for lifting you show on your index page! good idea. Thanks Mike

191

We are in the planning stages of lining and installing a new door on a pole barn this summer. The building has sliding doors now. The opening is 13'H X 16'W. The header is a rafter. We are considering a bifold door. Could you help us with some information and a rough price. Thank you! Dan S.

192

Pole Barn Builing,door mounting on gable end Standard: cable top & bottom seal 1- man door Option: 1- Free Standing Header

193

pole barn type hanger going up now going to need a door installed soon, 1-2 weeks 50' wide opening approx 14' tall clearance needed can you help ? thanks, jeff

194

Please give me an idea of the cost of replacing my barn door with a bi-fold hydraulic door on my building. The opening is 16' wide & 14' high. It has sliders now.

195

I am looking at buildfing a new pole building 30' x 50'. I would like a 12' x 26' openning once the door is fully openned. My neignbor is also considering a bifold on his new pole barn. Can u tell me what a bifold door would cost and who could intall it in Richland Center, WI. You may be able to ship two doors togther.... my neignbors building will be approx. 1000' from mine. -jim-

196

This is a pole building all wood frame wiyh sheet metal roof and siding; this is rough measurements its late and I,m tired; I hope if there is a little or- it wont make a big difference in price.I like the one piece door ;but will settle with what i can afford. I like to have the auto door opener please give me price on all opt. Thanks alot James S.

197

Dear Sir, I'm planning to build a hanger this summer near Selah, Wa. I anticipate it will be a 60x60 building with a 40 ft opening. A couple of questions: Is there a standard sized door that would be less expensive then a custom designed one? What is the normal height of the door? The hanger will be a pole barn type building. What design considerations should I be thinking about to accomidate the door? Ball park estimate? Thanks, Randy

198

This door is to be placed in the end wall of a pole building that has 12' tall side walls with a roof pitch of 4:12. Thanks Rich

199

looking for a quote on a new door for existing pole shed/shop. Installation, if you install or us? insulated door? door openers? Door with or with out windows. Give me a call if you have any questions. thanks

200

This is another request for the same size door except it is for a wooden pole building as your choices below are for one or the other.

201

Quote a price for a 18' x 12' door for a pole barn Just need a quick quote, to decide if I repair existing door or replace with a hanger type door. Thanks Dave S.

202

Have a pole barn/hanger with a 40' wide by 15' tall end wall opening. Header is a 5" by 21" glue lamb beam. Side posts are 8" x 8" pressure treated wood set in concrete. Door could be fastened near top of glue lamb beam which would give height of door at 15' plus say 18". Have 220 /110 volt power available. Would appreciate quote. Thanks, Wiley B.

203

The ceiling height will be 12' in my pole building. I need 12' clear height when the door is up. The width of the building will be 36', with a roof pitch of 6-12. Based on my call with you, it looks like the door will need to be 14' tall to get a 12' clear height.

204

I have a customer that builds pole buildings. They are my largest and best customer and I need to take good care of them. The building is being quoted to an airport here locally. They typically try to use overhead doors in these situations but its not finacially viable in most cases. I don't have any more specs than what I've given you. The exterior will be covered with painted steel panels. It will be on a gable end and have wood framing. Could you please quote a motorized unit and give me anything besides the basic door as an option If you could fax shop drawings as well. I NEED THIS ASAP. Thanks, Dean D.

205

I am intersted in putting a new door in a old wood pole type building that we use as a shop it has sliding doors in i now. I think it will need a free standing header to make it work. The RO is 20.5 feet wide and 13 feet high there is about 4 feet above the door to the roof line on the outside edges. It would have to be fully insulated. Please send me andy info and some idea of pricing if you can.